583758

Garmin GPSMAP 2110 Manual

27
Zoom out
Zoom in
Previous page
1/106
Next page
GPSMAP 2106/2110 Owner’s Manual 19
BASIC OPERATION > NAVIGATING TO A DESTINATION
To add a proximity waypoint:
1. Press the New Alarm soft key on the Proximity sub tab. The Find From
Current Position Page appears.
2. Highlight a category, and press ENTER.
3. Use the ROCKER to highlight a waypoint or map item, and press ENTER.
The Review Page appears for the selected waypoint or map item within a
red circle.
4. Press the OK soft key. The Proximity sub tab appears with the Distance
highlighted.
5. Press ENTER, and use the ROCKER to enter a proximity radius (up to
99.99 units).
6. Press ENTER when finished.
To turn proximity alarms on or off:
1. Use the ROCKER to highlight the field below Proximity Alarm on the
Proximity sub tab, and press ENTER.
2. Select ON or OFF, and press ENTER.
To clear one or all proximity waypoints from the list:
1. Use the ROCKER to highlight the proximity waypoint you want to clear.
2. To clear a single alarm, press the Delete soft key.
OR
To clear all proximity waypoints, press the Delete All soft key. A
confirmation message appears.
3. Press the OK soft key to delete the proximity waypoint. Otherwise, press
the Cancel soft key, or press QUIT to cancel.
Navigating to a Destination
Using the NAV key, the GPSMAP 2106/2110 provides four ways to navigate to a
destination: Go To Point, Follow Track, TracBack, and Follow Route. When you
are actively navigating, you see a straight line on the Map Page that always runs
from your current location to the destination. The easiest method for selecting a
destination is the Go To function, which allows you to select a destination point,
and then set a direct course to it from your present location. If you highlight
a point on a list or the map and press NAV, Go To <point name> appears in
addition to Go To Point. The Go To function can be accessed from any list of
points or from the map display.
DestinationCurrent location
Navigating to a Destination
… 27 …


Need help? Post your question in this forum.

Forumrules
1

Forum

garmin-gpsmap-2110

Reset search

  • I have acquired a Garmin 2110 with a GPS17.
    The cable between the two has been carefully cut - I assume to remove it from the previous vessel. I have connected all the cables together as per the Basic Installation shown in the handbook. All works fine.
    My question is how can i reconnect the two (front and rear) looms together. The wires from the GPS17 are too fine to solder and not of sufficient size as to allow connection by electrical Mobloc.
    Can anyone help me by telling me what they have used to connect these looms together?
    Thanks in anticipation
    Ian Hutchinson Submitted on 15-4-2021 at 11:46

    Reply Report abuse

  • I have just acquired a Garmin 2110 and GPS17.
    The wires that connect the two together have been carefully cut - I assume to enable the units to be removed from the previous vessel. I have connected all the wiring together as per the Basic Wiring diagram and all worked perfectly.
    However the wires from the GPS17 are extreamly delicate and will not (maybe my inexperience ) allow solder connections in order to make the installation complete. My question is what can I use to make a permanent fixing of the two (front and rear) looms?
    I have tried using a small mobloc but the wires in the GPS17 loom are too fine to make a good connection.
    Any help would be greatly appreciated
    Ian Hutchinson Submitted on 15-4-2021 at 11:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 2110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 2110 in the language / languages: English as an attachment in your email.

The manual is 6,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info