584000
52
Zoom out
Zoom in
Previous page
1/124
Next page
Page 4-16 400 SERIES INSTALLATION MANUAL
Page Rev L P/N 190-00140-02
4.8 VOR/ILS INDICATOR (GNS 430 ONLY)
4.8.1 VOR/ILS Indicator Function
NOTE
Because the GNS 430 includes a “CDI” button that performs switching between GPS and VOR/ILS on a
remote indicator, it is seldom necessary to use these outputs to drive an indicator. It is only necessary
when it is desired for a separate indicator to display VOR/ILS deviation full-time (regardless of the “CDI”
button status).
The VOR/ILS indicator displays both lateral and vertical, To/From indications, lateral and vertical flags
and superflags. GNS 430 connector 4006 always outputs the VOR/Localizer/Glideslope navigation
information. The VOR/ILS pins on GNS 430 connector 4006 are used to drive an indicator that displays
VOR/ILS information at all times, regardless of the CDI selection on the GNS 430.
VOR/LOC COMPOSITE OUT is a standard VOR/Localizer Composite output signal which may be used
to drive the Left/Right, TO/FROM, and Flag indications of certain navigation indicators that contain an
internal converter.
The ILS ENERGIZE output goes low when the VLOC frequency is channeled to a localizer channel.
4.8.2 VOR/ILS Indicator Electrical Characteristics
4.8.2.1 Superflags
Pin Name Connector Pin I/O
VOR/LOC SUPERFLAG P4006 15 Out
GLIDESLOPE SUPERFLAG P4006 38 Out
The output supplies not less than 500 mA on a 28 volt system and 250 mA on a 14 volt system with the
output voltage not less than (AIRCRAFT POWER - 3 V
DC
) when the flag is to be OUT OF VIEW. The
output voltage with respect to ground is less than 3 V
DC
when the flag is to be IN VIEW.
4.8.2.2 Deviation
Pin Name Connector Pin I/O
VOR/LOC +LEFT P4006 5 Out
VOR/LOC +RIGHT (VOR/LOC COMMON) P4006 6 Out
GLIDESLOPE +UP P4006 32 Out
GLIDESLOPE +DOWN/-FLAG (GLIDESLOPE
COMMON)
P4006 31 Out
The deviation outputs are each capable of driving up to three 1000 meter loads with ±150 mV
DC
±10%
with respect to 2.5V Common for full-scale deflection. The drive circuit provides for more than full-scale
deflection with a maximum course deviation output voltage of ±300 mV
DC
±10%.
4.8.2.3 TO/FROM
Pin Name Connector Pin I/O
VOR/LOC +TO P4006 1 Out
VOR/LOC +FROM (VOR/LOC COMMON) P4006 2 Out
The output is capable of driving up to three 200 meter loads. When indicating TO, the output is
+225 ±75 mV
DC.
When indicating FROM, output is -225 ±75 mV
DC.
When invalid information is present
(Flag IN VIEW) the TO/FROM output is 0 ±10 mV
DC.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 420 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info