584000
50
Zoom out
Zoom in
Previous page
1/124
Next page
Page 4-14 400 SERIES INSTALLATION MANUAL
Page Rev L P/N 190-00140-02
4.7 COM/VOR/ILS AUDIO (GNC 420 AND GNS 430 ONLY)
4.7.1 COM/VOR/ILS Audio Function and Emergency Mode
Activation of COM MIC KEY enables COM MIC AUDIO and causes the transceiver to transmit.
500 COM AUDIO and 500 VOR/ILS AUDIO are 100 mW audio outputs that are intended to drive a
headset or an audio panel.
Momentarily depressing the COM REMOTE TRANSFER button toggles the active and standby COM
frequencies. Momentarily depressing the VLOC REMOTE TRANSFER button toggles the active and
standby VLOC frequencies.
The COM REMOTE TRANSFER input may be used for EMERGENCY operation of the COM
transmitter. If the remote transfer switch is depressed for two seconds, the active COM frequency changes
to 121.50 MHz. Once the emergency frequency is activated through COM REMOTE TRANSFER, GNS
430 and GNC 420 COM transceivers with Mod 2 incorporated ignores inputs from the front panel controls
for COM selections only. The pilot may exit this independent mode—restoring COM selection control to
the front panel knobs and buttons—by momentarily depressing the COM REMOTE TRANSFER switch.
When TRANSMIT INTERLOCK is active, the GNC 420 or GNS 430 COM receiver sensitivity is
decreased. This input is intended to reduce interference from other transmitters in the aircraft. The
TRANSMIT INTERLOCK input should be connected to the PTT input of other transmitters in the aircraft.
If connected to multiple PTT inputs, these connections must include diode isolation or multiple radios
transmit simultaneously.
4.7.2 COM/VOR/ILS Audio Electrical Characteristics
4.7.2.1 COM MIC KEY
Pin Name Connector Pin I/O
COM MIC KEY P4002 4 In
This input is considered active if either the voltage to ground is < 1.9 V or the resistance to ground
is< 375 . This input is considered inactive if the voltage to ground is 11-33 V
DC
.
4.7.2.2 COM MIC AUDIO, INTERCOM MIC AUDIO
Pin Name Connector Pin I/O
COM MIC AUDIO HI P4002 6 In
COM MIC AUDIO LO P4002 18 In
INTERCOM MIC HI P4002 5 In
INTERCOM MIC LO P4002 17 In
COM MIC AUDIO and INTERCOM MIC each have a 520 AC input impedance and supply the
microphone with a 9 V bias through 620 .
COM MIC AUDIO is set in the factory for 275 mV
RMS
to modulate the transmitter at 80% nominally. The
microphone gain adjustment is accessible through the top cover.
When a 125 mV
RMS
signal at 1000 Hz is applied to the INTERCOM MIC input, the level on the COM
AUDIO output is not less than 7.07 V
RMS
.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 420 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info