584000
53
Zoom out
Zoom in
Previous page
1/124
Next page
400 SERIES INSTALLATION MANUAL Page 4-17
P/N 190-00140-02 Page Rev L
4.8.2.4 Flag
Pin Name Connector Pin I/O
VOR/LOC +FLAG P4006 3 Out
VOR/LOC -FLAG (VOR/LOC COMMON) P4006 4 Out
GLIDESLOPE +FLAG P4006 30 Out
GLIDESLOPE +DOWN/-FLAG (GLIDESLOPE
COMMON)
P4006 31 Out
The Flag output is capable of driving up to three 1000 meter loads. When valid information is present
(Flag OUT OF VIEW) the Flag output is 375 ±80 mV
DC.
When invalid information is present (Flag IN
VIEW) the Flag output is 0 ±25 mV
DC.
4.8.2.5 OBS
Pin Name Connector Pin I/O
VOR OBS ROTOR C P4006 9 Out
VOR OBS ROTOR H (GROUND) P4006 10 Out
VOR OBS STATOR D P4006 13 In
VOR OBS STATOR F P4006 12 In
VOR OBS STATOR E/G (VOR/LOC
COMMON)
P4006 11 Out
VOR OBS ROTOR C and H are a buffered 500 Hz output that is intended to drive the OBS rotors. VOR
OBS STATOR D and VOR OBS STATOR F are each phase and amplitude shifted version of the VOR
ROTOR C output. Each pair is intended to read one of the two windings of the indicator’s OBS stator.
4.8.2.6 VOR/LOC COMPOSITE
Pin Name Connector Pin I/O
VOR/LOC COMPOSITE OUT P4006 8 Out
With a Standard VOR Test Signal applied, VOR/LOC COMPOSITE OUT is 0.5 ±0.1 V
RMS
into a 10 k
load. With a Standard Localizer Centering Test Signal applied, VOR/LOC COMPOSITE OUT is 0.350
±0.05 V
RMS
into a 10 k load.
4.8.2.7 ILS ENERGIZE
Pin Name Connector Pin I/O
ILS ENERGIZE P4006 29 Out
The driver output voltage is not more than 1.0 V when sinking 20 mA. The maximum off state leakage
current with respect to GND is less than 10 µA.
4.8.3 VOR/ILS Indicator Configuration
Refer to section 5.2.13 for the VOR/LOC/GS configuration.
4.8.4 VOR/ILS Indicator Calibration and Checkout
Refer to section 5.2.13 for the VOR/LOC/GS checkout.
4.8.5 VOR/ILS Indicator Interconnect
Refer to Figure 4-21 on page 4-61 for the VOR/ILS indicator interconnect.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 420 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info