747917
201
Zoom out
Zoom in
Previous page
1/228
Next page
201
GO to TABLE OF CONTENTS
GovernorExpertGovernorExpert
This menu sets the Governor Expert parameters, allowing the user to further rene the governor settings.
"Governor Expert" screen from the "EXPERT MENU 3D" screen.
(1) Work Mode: Governor working mode
Sets the governing type mode.
- GOVERNOR (Governor Mode) – RPM is entirely controlled by the GOV
once it has engaged. The GOV will do whatever it takes to hold a constant
RPM throughout flight.
- Rev. Lmt (Limiter Mode) – Throttle control follows the throttle curves to
advance the throttle position during flight, but controls the RPM during
throttle reduction by not letting the RPM overspeed past the set RPM.
When the Rev.Lmt mode is selected, the menu (5) "THR. Mode" should be
set to Tx.Curve mode.
Setting:GOVERNOR/Rev.LmtInitialsetting:GOVERNOR
(2) Revo Disp: Governor working mode
This enables the user to display either the desired rotor RPM or the Engine
RPM accordingly.
Setting:Rotor/EngineInitialsetting:Rotor
(3) F/F. Cyclic: Feed Forward from Cyclic
Increasing the value will add throttle with cyclic commands to aid in RPM
stability.
Settingranges:0~100%Initialvalue:0%
(5) THR. Mode: Throttle data mode
This parameter selects the throttle input operation.
Optimize:
CGY sets the throttle input signal to optimum. There is no need to consider
the throttle curve setting on the transmitter.
Fixed:
This is the suggested mode for use with electric motors. This setting ensures
that there is a fixed throttle input as is related to the helicopter revolution.
Tx.Curve:
If this mode is selected, the CGY uses the exact throttle input from the transmit-
ter. As such, the throttle curve setting on the transmitter is required.
Note: when the Rev.Lmt mode is selected, this mode should also be selected.
Setting:GOVERNOR/Rev.LmtInitialsetting:GOVERNOR
(4) Yaw. Comp: Governor working mode
Yaw compensation allows the governor to more rapidly correct for changes
in power demands of the model resulting from yaw input. Set the mode to
match the gyro installation direction. Select from: CW/TOP, CW/BOTM,
CCW/TOP, CCW/BOTM.
Note: if the user has selected the governor only mode, this parameter is
inhibited.
Revolution fluctuation in the case of pirouettes
The governor detects the rpm via the revolution sensor mounted in the
engine section. During a pirouettes, the helicopter itself rotates, so that its
pirouettes speed is added (reduced) to the engine speed. Therefore, the
main rotor speed will fluctuate accordingly. Since the CGY has a gyro, it can
accurately measure the pirouette speed. The yaw rate correction is thus
determined by a combination of gyro function and governor function.
CW: clockwise rotor direction
CCW: counter clockwise rotor direction
TOP: Gyro top/name emblem facing up
BOTM: Gyro top/name emblem facing down
Setting:CW/TOP,CW/BOTM,CCW/TOP,CCW/BOTMInitialsetting:CW/TOP
201


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info