747917
202
Zoom out
Zoom in
Previous page
1/228
Next page
202
GO to TABLE OF CONTENTS
GovernorExpertGovernorExpert
(6) Revo. Up Dly: Revolution change up delay
How quickly the RPM changes when increasing RPM between two different
RPM conditions and flight modes. A higher number slows the RPM change
rate; a lower value speeds up the RPM change rate.
Settingranges:2~40
FrmInitialvalue:8
Frm
(7) Revo. Dn Dly: Revolution change down delay
How quickly the RPM changes when reducing RPM between two different
RPM conditions and flight modes. A higher number slows the RPM change
rate; a lower value speeds up the RPM change rate.
Settingranges:2~40
FrmInitialvalue:10
Frm
(8) Start Dly: Start delay
How quickly the RPM stabilizes to the set RPM from when the GOV is
turned ON. A higher value slows down the spool up rate; a lower value
speeds up the spool up rate.
Settingranges:2~20
FrmInitialvalue:5
Frm
(9) Gov. On. Revo: Governor ON revolution setting
This parameter tells the governor at what percentage of the set rpm it is to
become active. The default value is 60%. In this case, the governor will not
engage until the engine rpm reaches 60% of the set rpm. If you feel that
the time for governor engagement is too slow, decrease the value to 50 ~
55%. The starting time will be faster.
Settingranges:50~90%Initialvalue:60%
(10) BFS. Volt: Battery F/S voltage setting
This parameter sets the battery fail safe and low battery alarm voltage
levels, or thresholds. Set the proper voltage as determined by the bat-
tery type. The battery characteristics are different depending on cell type/
chemistry.
Suggested setting voltages are as follows.
•4cellsNiCdorNiMH(Normal:4.8
v)=3.8
v
•2cellsLiFe(Normal:6.6
v)=6.0~6.2
v
•2cellsLiPo(Normal:7.4
v)=7.2~7.4
v
(11) Low. Revo: Low revolution setting
This value is set to assign the lowest possible governing RPM. If the RPM is
below, or can not reach this RPM, the governor will not engage. Select be-
tween either 1,000
rpm or 700
rpm. It corresponds also to a helicopter with a
rotor speed of 1,000
rpm or less, such as a large gas machine.
Setting:700/1,000
rpmInitialsetting:1000
rpm
(12) RESET : Governor expert data reset
This resets the "Governor Expert" setting back to the defaults.
202


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info