747917
200
Zoom out
Zoom in
Previous page
1/228
Next page
200
GO to TABLE OF CONTENTS
SwashDetailSwashDetail
(12) ELE High / ELE Low: Linkage compensation elevator
At both the HIGH pitch and LOW pitch check to make sure that the swash
plate is staying level on the aileron and collective axis when using elevator
inputs. If the swash plate is rising or falling:
[Setting method] Operate the transmitter stick in the direction you want to
set. Touch the button lit in green to enter the setting mode and adjust the
mixing rate. Do the same for the other side.
Note: check all four directions: high/back; high/forward; low/back; low/for-
ward.
Settingranges:0~100%Initialvalue:0%
(13) ELE Dir: Compensation direction of the elevator
If the above Data (+/-) correction from 0-100 is NOT in the correct compen-
sation direction, change the value from [+] or [-].
Setting:+/-Initialsetting:+
(14) Speed Comp: Speed compensation
In 120 degrees CCPM all servos do not travel the same distance on eleva-
tor input. Having previously set the ELE-PIT and ELE-AIL parameters, if
during rapid movement of the elevator axis the swash plate is not staying
level, use the "Speed Comp" button to match all servo speeds. Note: a (+
will slow the Aileron/Pitch Servo – will reduce speed comp on Aileron/Pitch
Servo).
Settingranges:0~100%Initialvalue:H3-120=50%,exceptH3-120=0%
(15) SWASH Rot: Swash rotation
Using the "SWASH Rot" button, electronically add rotor head phasing to
the swash plate controls. If possible, it is recommended to use mechanical
phasing adjustment, but if the rotor head does not allow this and you feel
that the model is NOT flying axially on each control input, this parameter
can be used to adjust the pure reaction of each axis in flight. (Typically ad-
vanced phasing on clockwise rotor disk and a slight clockwise increase in
swash plate alignment vs rotor axle are needed to create an axial reaction.
The opposite is true for a counterclockwise rotor disk model.)
Settingranges:-90

deg~+90

degInitialvalue:+0

deg
(16) RESET : Swash detail data reset
This resets the "Swash Detail" setting back to the defaults.
200


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info