30098
13
Zoom out
Zoom in
Previous page
1/36
Next page
29 Charging and DSC (Direct Servo
Controller) connector
This connector is used as both the internal Nicad
battery charging connector and the DSC con-
nector.
Always charge the battery before use.
•Connect the DIN connector of the FBC-8B(2) charger
to the transmitter charging connector and the 3P con-
nector to the receiver/servo NR-4J battery, and plug
the charger into a 120 VAC outlet as shown in Fig. 24.
The battery can also be charged through the DSC-CHG
cord by installing the CHG adaptor to the charger as
shown in Fig. 24. The NR-4J receiver/servo Nicad bat-
tery can be charged while inside the aircraft.
•Normally charge the battery for about 15 hours.
When the battery
has
not
been
used
for some
time,
discharge it 2 to 3 times before charging.
(Leaving the battery discharged for a long time will
lower the battery capacity and shorten the battery
life.)
•The
transmitter
and
receiver
Nicad
batteries
can
be
charged simultaneously or independently.
•A fully charged transmitter battery can be used for
about 10 flights of 10 minutes each. The receiver and
servo NR-4J Nicad battery can be used for about 4
flights when used as a common power supply with the
rate gyro and for about 6 flights when a separate rate
gyro power supply is used.
Notes:
(1) First, connect to TX Nicd and red lamp goes on
(2) Then, connect to RX Nicd after connecting,
L,E,D, changes color from red to greenish red
(orange) which indicates that both TX and RX
Nicds are being charged.
(3)
In
case
of
separate charging,
L.E.D,
color
will
be: RX Nicd - Green TX Nicd - Red
•The
direct
servo
control
system connects the
sig-
nals from the transmitter directly to terminal C of
the receiver through a wire and controls the servos
without turning on the transmitter. It is extremely
convenient when ftying on the same band during
competitions, etc.
•Make the connections shown in Fig. 24. Connect-
ing ihe special DSC-CHG cord with tab to receiver
terminals C and installing it to the side of the aircraft
fuselage for convenience.
•When the DIN connector
of
the DSC cord is con-
nected to the DSC connector 29, the power to the
encoder inside the transmitter is turned on. Se; the
transmitter power switch to OFF.
•When not using the DSC. disconnect the DIN con-
nector.
•To operate the servos, turn on the receiver and
servo switches.
1
1
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSHP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info