Manual Futaba FP8SSHP (page 12 of 36) (English)

30098

Zoom out

Zoom in

1/36

MODE SEL KEY SW.

2 UP TIMER

Set the tachometer/timer POWER switch to ON.

is displayed. Next, press the MODE.SEL

key switch at the upper right-hand corner one time.

The display changes to , and the UP

TIMER mode is selected. When the ENTER key

switch at the bottom right-hand corner is pressed, a

beep is head and the timer starts and the second

digit of the display changes every second. A beep is

produced every minute to indicate the passage of

time. To stop counting, press the ENTER key

switch again. The usage time is displayed on t he dis-

play. For example, S means that 12 minutes

05 seconds had elapsed. The UP TIMER mode can

be used as a second stop watch. To clear the dis-

play, press the ENTER key switch again.

ALARM SETTING

The alarm can be set with the TIME SET key. Clear

the display, by pressing the ENTER key, then press

the TIME SET key twice.

appears on the display indicating that

two minutes was set. Next, press the ENTER key

once to memorize this two minutes The display

changes to and is memorized. Start the

timer by pressing the ENTER key. The display

changes every second. When the display reaches

5 1 fhe timer keeps ten times, every once

a second, to indicate that two minutes have

elapsed. Thereafter the timer continues to count

up to 60 minutes. If the TIME SET key is pressed

and held for two seconds or longer when memo-

rizing the alarm time, the time is set in five minute

steps and the set alarm times are memorized until

the power is turned off or reset. If the timer is

started without setting the time after the display

has been cleared, the previously set alarm time

remains effective. An arbitrary alarm time up to

59 minutes can be set.

(3 DOWN TIMER

Set the tachometer/timer POWER switch to ON

and press the MODE SEL key twice.

appears on the display to indicate that

the DOWN TIMER mode was selected. Next,

press the ENTER key. The timer keeps.

appears on the display, and the display begins to

count down every second. The timer keeps every

Fig.

second from 10 seconds before the end of the

count-down, the same as the UP TIMER.

TIME AND ALARM SETTING

Set the time and alarm with the TIME SET key,

the same as the UP TIMER. To set the alarm to

at the display, clear the display by

pressing the ENTER key, then press the TIME

SET key three times. Next, memorize this time

by pressing the ENTER key again. The display

begins to count down in seconds. When the dis-

play begins to count down in seconds. When the

display reaches the timer begins to

keep every second to indicate that three minutes

have elapsed. If the TIME SET key is pressed

and held for two or more seconds, the time is set

in five minute steps, the same as the UP COUN-

TER, and the alarm can be set to any desired

time up to 33 minutes.

4) INTEGRATING TIMER

Set the tachometer/timer POWER switch and the

transmitter power switch to ON. The blinks,

counting begins, and the elapsed time is displayed

in minutes. For example, indicates that

three minutes have elapsed. If the transmitter

power switch is set to OFF, counting stops. When

the transmitter power switch is turned back on,

counting continues. The integrating timer func-

tion can be started and stopped as long as the

tachometer/timer POWER switch is on even if

another mode is selected with the MODE.SEL

key. This can be used to monitor the transmitter

operating time If the ENTER key is pressed in

the INTEGRATING TIMER mode, the old in-

tegrating time is cleared and a new count begins.

This can be used to forecast the remaining

Nicd

battery capacity and other applications.

28 Tachometer sensor connector

The tachometer sensor connects

this

connector as

described in the preceding item.

When this connector and charging

connector [29] are

not in use, cover them with the rubber-backed cover

supplied.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSHP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba FP8SSHP Manual

Product: