30098

Futaba FP8SSHP Manual

8
Zoom out
Zoom in
Previous page
1/36
Next page
22 Hovering throttle ratcheted knob
•Trims the throttle servo independently from the
pitch control servo (without regard to mixing).
Since
the throttle
servo
can
be
trimmed
without
interfering with other mixing, this knob is very
convenient when trimming the throttle while
hovering.
• When the throttle lever
[3]
is at about the center,
the throttle servo throw can be adjusted about
25% of the total travel with this knob.
•When the throttle lever
[3]
is at the low
or high
sides, the throttle servo does not operate even if
this knob is turned.
24 Monitor lamps
Lamp ®
Fig.
14
Lamp B Lamp C Lamp D
Throttle servo
total travel
Adjustable within this
range with knob 22 .
Throttle servo
Fig.
13
23 Throttle hold switch (TH switch)
Right ON, Left OFF.
•This switch is used during auto-rotation. If this
switch is set to ON when the throttle lever [3] is
in the maximum slow position, the throttle servo
will stop at the position (idling or engine stop)
set at trimmer
[8]
on the trimmer panel at the
back of the transmitter. At this time, the time set
at trimmer
[7]
(throttle hold delay) is applied and
the pitch control servo is set to the optimum
pitch for auto-rotation set with trimmer
[5].
This
setting can be made without regard to the posi-
tion
of the
pitch
control
high
side
trimmer
lever
[13 ]
•When fail safe switch [12] on the trimmer panel
at
the back of the transmitter is set to the INH posi-
tion, the throttle hold function is inoperative.
When it is set to the T.HOLD position, monitor
lamp [D] comes on to indicate that the throttle
hold function is set.
If the TH switch [23] is then set to ON, lamp [D]
goes out to indicate that throttle hold is being
performed.
Lamp
A
When the power switch [30] is set to ON, this lamps
comes on and the pointer of the level meter de-
flects. At FS data transmission, this lamp goes out
momentarily and data transmission can be moni-
tored. The lamp goes out once every 60 seconds.
When the internal Nicd battery approaches full
discharched, this lamp starts blinking. This alarm
indicates that the power error backup function is
activitated the memory and circuit (memory, ATV,
FS, etc.) is not functioning.
Lamp
B
When fail safe switch [13] on the trimmer panel at
the back of the transmitter is to the IDLE 1 posi-
tion (idle up 1 function ON), this lamp lights.
When the idle up 1 switch [19] is set to ON, this
lamp goes out.
Lamp
C
When
fail safe switch
[14]
on the trimmer panel at
the back of the transmitter is set to the IDLE 2
6
position (idle up 2 function ON), this lamp comes
on. When the idle up 2 switch [21] is set to ON,
this lamp goes out.
Lamp
D
When fail safe switch [12] on the trimmer panel at
the back of the transmitter is set to the T.HOLD
position (throttle hold function ON), this lamp
comes on. When the throttle hold switch [23] is set
to
ON, this lamp goes out.
When the power switch [30] is set to ON, lamp [[A]
will go out momentarily. This indicates automatic
data transmission on and is not a failure.
Functions priority
Lamp B (Idle up 1 )
Lamp C (Idle up 2 )
Lamp D (Throttle hold)
The function priority is hold -> idle up 2 -> idle
up 1 . Lamps B, C, and D come on when the
pertinent fail safe switch (13, 14, 12) is set to the
ON position. When the idle up 1 switch [19] is set
to ON, lamp
[B]
goes out. Keeping the idle 1
switch [19] in the ON position, try setting the idle
up 2 switch [21] to ON. Lamp B comes on and
lamp [C] goes out, indicating that the idle up 2
function has priority. Similarly, if the throttle
hold switch [23] is set to on while the 1 switch
[19]
and 2 switch
[21]
are ON, lamps B and C go out,
indicating that the throttle hold function has
priority.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSHP in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info