30094

Futaba FP8SSAP Manual

19
Zoom out
Zoom in
Previous page
1/44
Next page
ADJUSTMENTS AND FLIGHT TECHNIQUES
•USING
ATV
(ADJUSTABLE
TRAVEL
VOLUME)
GENERAL - ATV (Adjustable Travel Volume)
allows independent adjustment of servo maximum
throw in each direction (without affecting the
neutral position). This is also sometimes referred
to as "separate endpoint adjustment". ATV is very
convenient when for example: a model requires
more DOWN elevator deflection than UP for equal
inside and outside loops (with equal control stick
deflection). Other aircraft may require slightly
different RIGHT or LEFT aileron or rudder
deflection to give equal response in each direction
(due to engine torque, precision of the model,
etc.). Two different ATV functions are possible
with this system. Memory (Pushbutton) ATV and
2ND
ATV.
MEMORY (PUSHBUTTON) ATV
This type of ATV is available on all eight channels.
Servo travel is adjusted as outlined in the example
below.
NOTE: Memory ATV settings are retained in the
transmitter memory circuit even when the power
switch is turned OFF. They are lost however, if
the transmitter
Nicd
battery
nears
full
discharge
or
is removed for servicing.
ATV SETTING
Switch switches S [
49] and R [48]
Press button [46] or [47] while holding the aileron
stick in the full position.
Fig.
20
MEMORY (PUSHBUTTON) ATV - (Aileron CH1
used as example)
1. First, set Function Select Switch [49]
to
ATV
position.
2. Set Channel Select Switch [48]
to 1 (Ail.).
3.Set
the transmitter and
receiver
power switches
ON and check for proper servo operation.
4.Move the Aileron stick to full RIGHT aileron,
hold it in that position, and set servo movement
to the desired Right aileron deflection angle by
pressing Button 46 or 47].
5.Repeat Step 4 for LEFT aileron.
6. For other
channels,
select
the channel
with
switch 48 and adjust ATV as desired.
7. When all adjustments are completed, set the
Function Select and Channel Select switches
([48]
and
[49)
to
OFF.
8. To clear the ATV settings on all channels, set
the Function Select switch [49] to RESET and
Channel Select switch [48] to POSITION 2 (Pos.
2 = ATV when [49] is on RESET) and press
Buttons 46 and [47] simultaneously. ATV is
cleared
on
ALL
CHANNELS and
servos
will
move to 100% of their maximum throw.
9. If only one channel is to be cleared or changed,
simply repeat Steps I through 5 with Chan-
nel Select Switch [48] set to the appropriate
channel.
1
7
ATV/FS BUTTON
•These two pushbutton switches are used for servo deflection angle setting of ATV. FS or HOLD func-
tion, servo test start & stop; reset; battery FS memory set, etc.
——————————————————————[46]
This
pushbutton
switch
is
used
when:
1 Making the ATV servo deflection angle larger.
2 Turning the FS function on.
3 Starting
the
servo
test.
[47] This pushbutton switch is used when:
1 Making the ATV servo deflection angle smaller.
2 Turning the HOLD function on.
3 Stopping the servo test.
When button [46] and [47] are pressed at the same
time, reset or battery FS memory setting is pos-
sible. At this time, lamp A of memory lamps 22
goes out momentarily so that setting can be moni-
tored.
Fig.
21
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSAP in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info