29053

Futaba 9ZHP_part2 Manual

27
Zoom out
Zoom in
Previous page
1/78
Next page
Helicopter Section
19
Gyro Sensitivity Switching
Gyro Sensitivity switching may be set for each
flight condition. To set sensitivity, call the Gyro
Sensitivity Function
GYR
from the condition
menu.
Assuming that the sensitivity of the gyro is set so
that the 1 side was made low sensitivity, and the 2
side was defined as high sensitivity, set the type at
each flight condition as follows:
Normal
.......
Type 2
Idle-up
1
.......
Type
1
Idle-up 2
.......
Type 1
Autorotation .... Type 1 (if the tail rotor is
driven during auto-
rotation, high gyro
sensitivity (type 2)
may be more effec-
tive.)
20 Engine Cut Setting
At the conclusion of a flight, you may use the
Engine Cut function to kill your engine by one
touch with a special switch. Because it is performed
by stick lever, there is no need to fumble for the
trim position, and the idle trim position need never
be lost.
Press the Engine Cut
CUT
button from the
model menu, activate it, and set the desired switch.
Set the throttle a bit above the lowest throttle posi-
tion, then press the
SET
button to memorize the
position. This makes it so the engine cut function
will only operate when the throttle is at the idle
position, so the engine can't inadvertently be shut
off.
Adjust the throttle servo motion so that there is
no binding or excess travel.
21 Condition Hold Setting
If you want to set condition data while the
engine is running, always use the Condition Hold
function
CHD
to limit the throttle operation range.
Press the CHD button on the Model menu. Set the
maximum throttle position to be a bit above the idle
position, and press the
SET
key. This should
produce a maximum throttle setting of about 13%.
Be sure not to set the maximum too high.
You may activate the Condition Hold menu from
the Home menu (use the G key), from the Model
menu (2nd line, G key), or from the Condition
menu (use the
M
key). When Condition Hold is
activated, a double beep repeats every few seconds
to remind you that it is engaged, so that you do not
attempt to fly with it on. This setting allows you to
control the throttle between 0% and 13% with the
throttle stick when the function is activated.
This concludes the setup procedure example. Be
sure to browse through the pages following this
example to see what other menus are available for
helicopters, such as
HOF . GYR , ACC ,
and
INV
. Many may be used to enhance flight capa-
bilities or to correct bad tendencies. All of these
menus may have different settings in different flight
modes. For this reason, we recommend you set them
up and use them in the Normal flight condition and
trim the model before setting up the alternate flight
modes.
Helicopter Section, Page 103
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info