29011

Futaba 9ZHP_part1 Manual

64
Zoom out
Zoom in
Previous page
1/78
Next page
Common Condition Section
ADJUSTABLE FUNCTION RATE (AFR)
This function is used to adjust the throw and
operation curve of the stick, lever, and switch
functions (CH1 to CH8) for each flight condition.
This is normally used after ATV has defined the
maximum throw directions (ATV acts on ALL
flight condition settings). When mixing is applied
from one channel to another channel, both chan-
nels can be adjusted at the same time by adjusting
the operation rate by AFR function.
In the AFR mode, the function operation rate
can be adjusted for each travel direction. The
servo's response curve can be changed so that the
control can be performed comfortably by setting
the EXP1/EXP2 modes. This is best understood by
examining the curves that the PCM 1024Z system
displays as the parameters are changed. The AFR
function may be programmed to have a rate varia-
tion from 0 to 140%; the EXP1/EXP2 curve rate
can be adjusted from -100 to +100%. With 0%,
exponential produces a normal straight-line
response.
In the EXP1 mode, the servo movement near
the neutral position can be made sensitive or in-
sensitive. EXP2 mode is applicable to throttle and
other control sliders and levers that do not self-
center, and changes the response shape at one end
of the control movement. The response rate can be
made steep or gradual. NOTE: if you activate the
throttle curve and pitch curve functions, the throt-
tle channel and pitch channel EXP curves are
overridden.
If the LIN mode is defined within the EXP1
mode, you can make an ordinary rotary servo have
similar motion to that of a linear servo. In other
words, the rotary servo moves more the further it
is away from neutral, to simulate a linear output,
which moves the same amount regardless of servo
position.
Adjusting Function Rates
Activation of command
In the Condition Menu, press the
AFR
key to get the
AFR menu shown below.
Mode setting
Channel Setting
Rate setting
(Side A)
Rate setting
(Side B)
Return to condition menu
To next screen
Channel Selection
To enter the channel selection menu, press the B key.
and then press the key of the channel you wish to set.
Depending on the Model setup, the following keys will
appear on the bottom of the screen:
Airplane:
Helicopter:
Sailplane:
Input Rates
You can select the rates in both directions, which are
designated as "A" and "B". To enter the rate for Side A,
press the C key and use the rate setting keys F to El to
input your desired rate. The rate is initially set to 100%.
Press the numeric key nearest the rate you desire from
among the H (0) to M (
100
) keys. You can then
increase and decrease the selected value with the F(+)
and G (-) keys. Each key press adds or subtracts 1.
Set the movement up so that no binding occurs at any
extreme motions of sticks, knobs, or sliders. You may set
the travel to anywhere between 10 and 140%.
Now you will set up Side B's rate similarly. Press the
D
key and set the rate with the rate setting keys F to
M.
As before, use the numeric keys to get the travel you
desire.
Repeat this procedure for all the channels in sequence.
Common Conditions Section, Page 62
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part1 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info