747924
16
Zoom out
Zoom in
Previous page
1/23
Next page
16
3PV-2.4G Functions
Model Selection
Model Reset
MDL
Low Battery Alarm
LBA
System Type
SYS
The model selection selects the desired model memory from the 10 model memories stored
ZLWKLQWKHWUDQVPLWWHUDQGWKHPRGHOUHVHWHUDVHVDOOGDWDVWRUHGLQDVSHFL¿FPRGHOPHPRU\
Model Name
MDL NAME
Model number
1 - 0
Model name
Model Reset
Push the DT1 lever right or left
for about two seconds.
All data stored in the currently
selected model memory is
erased.
Model Selection
Selection key
This function provides a
4-character name for each of the
model memories in the transmitter
to easily select the correct setup
for the model currently in use.
Clearly label each model for easy
selection.
Select the battery alarm voltage
according to the battery to be used.
*The voltage drop of a rechargeable battery
and a dry cell battery is different. When
using a rechargeable battery, always change
the voltage.
System changes (T-FHSS, S-FHSS,
FHSS, T-FHSS <High-Speed>)
matched to the receiver type.
Ɣ
4 dry cell batteries
4.2V
Ɣ
HT5F1800B (5cell NiMH battery)
5.0V
Ɣ
FT2F1700BV2/FT2F2100BV2 (2cell LiFe battery)
5.8V
Model Name
(Selection)
Model number
1 - 0
Model name
(Selection key)
Low battery voltage
Alarm start voltage
Voltage change
System Type
TFH: T-FHSS
SFH: S-FHSS
FH: FHSS
TFH-HS: T-FHSS High-Speed
System change
Ɣ
R314SB/R304SB
T-FHSS (TFH), T-FHSS High-Speed (TFH-HS) : The voltage of the receiver is shown to a transmitter.
Ɣ
R203GF
−−−
S-FHSS (SFH), FHSS (FH)
When using the T3PV in the T-FHSS High-Speed mode, always use it under the following conditions:
Servos :
Futaba digital servo (including BLS Series brushless servos)
Receiver’s battery :Matched to the ratings of the receiver and connected digital servo (dry cell battery can-
not be used).
Under other conditions, the set will not operate, or the specified performance will not be displayed even if it
operates. In addition, it may cause servo trouble.
Power Switch: OFF
ON
When the system was changed and
when a model of a different system
was selected, signal are output in the
system set at the point at which the
transmitter power was turned back on.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 3PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 3PV in the language / languages: English as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info