747924
15
Zoom out
Zoom in
Previous page
1/23
Next page
15
*When making these setting adjustments, do so with the motor disconnected or the
engine not running.
NEUTRAL, HIGH, AND BRAKE MAX POINTS SETTINGS
Before setting each point, set the transmitter throttle channel trim to neutral.
Turn on the power in transmitter -> amp order.
1
2
Transmitter throttle operation
Neutral state
Press the pushbutton switch.
(0.5 secs or longer)
(Confirmation beep sounds)
Continuous single blink
MC231CR /MC331CR
(Pushbutton switch operation) (Checker LED)
N
N
Full High
Full brake
N
Neutral point
setting
3
Full high state
Press the pushbutton switch.
(Confirmation beep sounds)
Continuous double blink
High point
setting
4
Full brake state
Press the pushbutton switch.
(Confirmation beep sounds.)
If the LED goes out,
setting is complete.
Brake MAX
point setting
Set the throttle adjustment function (EPA) to 100% and
the ABS function to OFF using the transmitter throttle
channel function.
If the throttle angle is too large or the ABS functions are on,
erroneous operation may occur.
*When using the ABS function,
after setting up the MC231CR /
MC331CR, stop the reverse
function, then turn on the ABS
function. If the ABS function is
on, the MC231CR / MC331CR
cannot be set up correctly.
(Preparations)
Select the model memory that is not used and reset it to the initial values with the model
selection and model reset functions.
Servo Horn Installation Instructions
1
Connect the receiver, servos, and other components and then turn
on the power switches to the transmitter and receiver.
*Both servos will move to the neutral position.
2
At this time install the servo horn in the manner described in the
instruction manual provided with the model this system will be used in.
Reversing The Servo Operation Direction
Should the servo operate in the opposite direction required for your application,
reverse the direction with the servo reversing.
E.S.C. MC231CR / MC331CR
Transmitter Set-Up Procedures
Model number
1 - 0
Model name
Model Reset
Push the DT1 lever right or left
for about two seconds.
All data stored in the currently
selected model memory is
erased.
Model Selection
Selection key
Throttle Servo Reverse
NOR: Normal
REV: Reverse
Direction change
NOR: Normal
REV: Reverse
Steering Servo Reverse
Direction change
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 3PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 3PV in the language / languages: English as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info