747924
13
Zoom out
Zoom in
Previous page
1/23
Next page
13

Check the receiver, servos, and battery connectors, to be sure they are firmly
connected.
If a connector is not fully inserted, vibration may cause the connector to work loose
while the model is operating. This will result in loss of control.
Operate each servo horn over its full stroke and check to see that the linkage does
not bind or is not too loose.
Excessive force applied to the servo horn by binding or poor installation may lead to
servo problems and result in loss of control.
(Electric Cars and Boats)
Isolate the receiver from vibration by attaching to the chassis or mounting plate with
thick double sided tape.
(Gas Powered Cars and Boats)
Isolate the receiver from vibration by wrapping it in foam rubber or similar type
cushioning material. Protect the unit from water damage by placing it in a plastic
bag or waterproof radio box.
The receiver contains precision electronic parts. These parts are vulnerable to vi-
bration and shock. Any contact with moisture (water or condensation) may cause
receiver malfunction and loss of control.
Keep all devices that emit high frequency noise, such as motors, batteries, and
wiring that handles heavy current loads, at least 1/2 inch away from the receiver
and the receiver antenna.
High frequency noise will cause a decrease in operating range and could cause
loss of control.
Install electronic speed control heat sinks as well as other components that conduct
electricity so they cannot come in contact with aluminum, carbon fiber or other
materials that conduct electricity.
If, for example, the speed control came loose while the model was running and
touched an aluminum chassis, a short circuit may occur that would cause irrepa-
rable damage to the system as well as loss of control.
Noise suppression capacitors should be installed on almost all motors.
If the proper capacitors are not installed, high frequency noise will reduce range
and cause loss of control along with various other problems.
Inspect all linkage installations and any point where metal could come in contact
with other metal parts. Make sure these parts do not touch other metal parts under
vibration.
Should a linkage or other metal parts come in contact with other metal parts under
vibration, the high frequency noise generated by this contact will cause interference
and possible loss of control.

Do Not disassemble any part of this system that is not specified in the instruction
manual.
Futaba will not be responsible for any damage due to improper disassembly of any
part of the radio control system.
Assembly Precautions
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 3PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 3PV in the language / languages: English as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info