624064

Fluke networks TS23 PRO Manual

16
Zoom out
Zoom in
Previous page
1/22
Next page
12
TS23 PRO Test Set
Users Guide
Configuring Your Test Set
The test set stores all settings in non-volatile memory.
The settings do not change if you change the battery.
Hook Flash Duration
When the test set is off-hook, and you press F, a
timed interruption of the loop current occurs. Some
PBX setups or telephone office switches use this signal
to put a call on hold or to activate a special function.
Each key press generates one flash.
You can select durations of 100 ms to 900 ms in
increments of 100 ms. The default is 500 ms.
To set the flash duration:
1
Press Q.
2
Press S, then F, then press a number key.
For example, 1 sets the duration to 100 ms.
Test Set Timeout
The test set turns off after a specified period of
inactivity. The default period is 2 minutes. The timer
starts again when you press a key or when the test set
is in Monitor mode and receives a call.
To change the test set timeout period:
1
Press Q.
2
Press S, then *, then press a number key:
•
1 = 1 minute
•
2 = 2 minutes
•
3 = 5 minutes
•
4 = 10 minutes
•
5 = 30 minutes
•
6 = 60 minutes
Make Receive-Only Loud Speaker Mode the
Default
When you put the test set in the off-hook mode and
press
s, the Speakerphone turns on. If you then
press
N, the Receive-Only Loud Speaker is enabled
temporarily. When the Receive-Only Loud Speaker is
enabled, the speakerphone microphone turns off and
the test set can only receive audio signals – it cannot
transmit any audio signals. Receive-only is preferred
when your main concern is to listen to the line and you
do not want ambient noise such as caused by a passing
car to switch the Speakerphone into transmit mode.
If you frequently have two-way conversations, then
you probably want the Speakerphone to be the
default mode for the speaker. If you mostly listen when
the speaker is on, then you may want the Receive-Only
Loud Speaker to be the default mode for the speaker.
To set Receive-Only Loud Speaker as the default mode
for the speaker:
1
Press Q.
2
Press S, then press N.
To turn on the speakerphone microphone, do the steps
above again.
Factory Defaults
You can set all programmable features to their original,
factory settings. This function does not delete stored
telephone numbers. The defaults are:
•
Hook flash duration: 500 ms
•
Speakerphone microphone: on
•
Handset volume: level 4
•
Speaker volume: level 4
•
Tone/Pulse: tone
•
Receive-Only Loud Speaker mode: disabled
To restore factory defaults, Press
S, then press #.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke networks TS23 PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke networks TS23 PRO in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info