Manual Florabest FBK 4 C2 - IAN 296309 (page 17 of 42) (English)

679143

Zoom out

Zoom in

1/42

FBK 4 C2

■ 12

│

GB│IE│NI

Installing/replacing the strimmer

■ Install/replace the strimmer as displayed in ﬁgure 2c.

■ Find the hole in the drive plate



, align it with the opposite hole and

block it with the supplied hex key



■ Screw the strimmer onto the thread in an anticlockwise direction.

ATTENTION! Left-hand thread!

Putting on the carrying harness

NOTE

■

The following adjustments can be made to make sure that you can

work without becoming fatigued. The settings may vary depending

on your body size.

■ Before starting work, adjust the carrying harness



to suit your body

size.

■ Balance the appliance with the ﬁtted cutting tool so that the cutting

tool swings just over the ground without the need to move the appli-

ance with your hands.

1.) Put on the carrying harness



and close the clasps so that they click

into place (see ﬁg. 3a).

2.) As shown in ﬁgure 3b, pull on the belt



, to position the carrying

harness



centrally on your body and adjust the upper body size.

3.) To tighten the two shoulder straps, pull on the two shoulder straps as

shown in ﬁgure 3c.

4.) To ensure to the correct position of the appliance on the carrying harness,

pull the belt as shown in ﬁgure 3d.

5.) Hook in the carabiner

(see ﬁgs. 3e–3g) and secure it with the red

strap

on the quick release mechanism.

6.) Now take the appliance and hang it so that the carrying lug

clicks

into the carabiner

, as shown in ﬁgure 3h. The carrying lug can

also be moved by loosening the screw

and sliding it to achieve the

optimum orientation of the appliance.

Setting the cutting height

■ Put on the carrying harness



and hook in the appliance (see section

"Putting on the carrying harness").

■ Use the various belt straps on the carrying harness



to adjust the

optimum working and cutting position (see section "Putting on the

carrying harness").

■ Perform a few circular movements without starting the engine in order to

ﬁnd the ideal shoulder strap length (see ﬁg. 6a).

■ The carrying harness



is equipped with a quick release mechanism.

Pull on the red strap if you have to release the appliance quickly

(see ﬁg. 3i).

CAUTION!

■ Always use the carrying harness



when working with the device.

Put on the carrying harness



as soon as you have started the

engine and it is ticking over. Turn oﬀ the engine before removing the

carrying harness



Fuel and oil

■ Only use a mixture of unleaded petrol (at least RON 95) and special

2-stroke engine oil (JASO FD/ISO-L-EGD). Mix the fuel mixture in ac-

cordance with the fuel mix table.

■ Add the respective correct amounts of unleaded petrol and 2-stroke oil

to the supplied oil/petrol mixing canister



(see "Fuel mix table").

Then shake the canister well.

Fuel mix table

Mixing process: 40 parts petrol to 1 part oil

Petrol 2-stroke oil

0.5 litres 12.5 ml

Use

CAUTION!

■ Please pay attention to the statutory provisions in the relevant noise

protection regulations.

Before starting the appliance, always check that:

■ The fuel system is not leaking.

■ The protective equipment and cutting equipment is complete and in

perfect working order.

■ All screw connections are ﬁrmly tightened.

■ All moving parts can move smoothly and freely.

Starting when the engine is cold

CAUTION!

■ Never allow the starter pull cord to whip back. This could cause

damage.

1.) Fill the fuel tank

(see also the section "Fuel and oil").

2.) Push the fuel pump (primer)

6 times.

3.) Switch the On/Oﬀ switch

to "I".

4.) Pull the choke lever

into the position " ".

5.) Hold the appliance ﬁrmly and pull out the starter pull cord

to the

point of ﬁrst resistance. Now pull hard on the starter pull cord

The appliance starts.

6.) If the engine does not start, repeat step 5.

7.) As soon as the engine is running, press ﬁrst the safety lock-out

and

then the throttle

to activate the automatic choke.

If the engine does not start after several attempts, read the "Troubleshooting

guide" section.

CAUTION!

■ Always pull the starter pull cord

straight out. Hold the handle of

the starter pull cord

ﬁrmly when the starter pull cord

retracts.

Do not allow the starter pull cord to whip back.

NOTE

■ At very high ambient temperatures, it is possible that even a cold

engine has to be started without using the choke!

Starting when the engine is hot

(The appliance has been turned oﬀ for less than 15–

20 minutes)

1.) Switch the On/Oﬀ switch

to "I".

2.) The choke lever

does not need to be pulled out to start a warm motor.

3.) Hold the appliance ﬁrmly and pull out the starter pull cord

to the

point of ﬁrst resistance. Now pull hard on the starter pull cord

. The

appliance should start after 1–2 pulls. If the appliance still hasn't started

after 6 pulls, repeat steps 1–7 under "Starting when the engine is cold".

Hvor kan man købe reservedele? Jeg mangler en fjeder der sidder i huset hvor starts snoren sidder Submitted on 24-3-2021 at 14:32
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBK 4 C2 - IAN 296309 in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FBK 4 C2 - IAN 296309

Florabest FBK 4 C2 - IAN 296309 User Manual - German, Dutch, Danish, French - 78 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Florabest FBK 4 C2 - IAN 296309 Manual

Product: