Manual Florabest FBK 4 C2 - IAN 296309 (page 16 of 42) (English)

679143

Zoom out

Zoom in

1/42

FBK 4 C2

GB│IE│NI

│

11 ■

Tightening and checking the saw chain

WARNING!

► Wear protective gloves! There is a danger of injury from the sharp

cutting teeth!

♦ Turn the chain-tensioner screw

in a clockwise direction using the

ﬂat-blade screwdriver



to increase the tension.

♦ The saw chain

must lie against the underside of the blade. Check

whether the saw chain

can be drawn over the blade

by hand.

NOTE

►

A new saw chain

stretches and must be tightened more frequently.

Lubricating the chain

♦ Remove the oil ﬁller cap .

♦ Fill the oil tank

with approx. 100ml of organic chain oil



♦ The chain lubrication can be increased or decreased using the oil

adjusting screw

♦ Press and then turn the oil adjusting screw

clockwise to decrease

the chain lubrication.

♦ Press and then turn the oil adjusting screw

anticlockwise to increase

the chain lubrication.

WARNING!

► Never work without lubricating the chain ﬁrst!

If the saw chain runs dry, the cutting equipment may become irrepar-

ably damaged within a short time. Always check chain lubrication

and oil level in the tank before starting work.

NOTE

► Use only saw chain oil. Preferably biodegradable. Do not use waste

oil, motor oil, etc.

► While working, check whether the chain lubrication is working

correctly.

Sharpening the saw chain

NOTE

►

A bench grinder can be attached to the bench grinder support

for

a secure grip during grinding.

► You will ﬁnd detailed information on sharpening in a sharpening set,

e.g. from Oregon.

► Alternatively, you can use an electrical saw chain sharpening device

and follow the manufacturer's instructions.

► If you have any doubts about carrying out the work, the saw chain

should be replaced.

Attaching the extension attachment

CAUTION!

■ Do not use the extension attachment/boom



in combination with

the 3-section cutting blade/strimmer attachment!

NOTE

► Use the extension attachment/boom



for working at greater

heights.

♦ Fit the extension attachment/boom



between the engine unit and

the hedge trimmer/pole pruner. The assembly is carried out in the

same manner as for the attachments described previously.

Fitting/removing the protective guard

WARNING!

■ When working with the 3-section cutting blade

, the blade guard

must be ﬁtted. The blade guard is positioned under the metal panel

of the boom . The blade guard is now attached to the front boom

with the 2 screws . To do this, use the supplied hex key



Cutting equip-

ment

Protective equipment

3-section cutting blade Blade guard

Strimmer

Blade guard + cutting ﬁlament protect-

ive guard

WARNING!

► Do not use any other cutting equipment apart from that which is

supplied with the product. The use of any other cutting equipment

or protective equipment is deemed to be improper and carries a

signiﬁcant risk of accidents.

Installing/replacing the cutting blade

■ Fit/remove the 3-section cutting blade as shown in ﬁgures 1a–1f.

■ Find the hole in the drive plate



, align it with the opposite hole and

block it with the supplied hex key



■ Place the 3-section cutting blade on the drive plate



(see ﬁg. 1b).

The inscription must be visible from above when holding the tool in the

working position (see fold-out page). Both sides of the 3-section cutting

blade can be used.

■ Fit the pressure plate



over the thread over the splined shaft (see ﬁg.

1c).

■ Fit the pressure plate cover



(see ﬁg. 1d).

■ Tighten the nut



with the spark plug spanner



anticlockwise ACH-

TUNG! Left-hand thread! (see ﬁg. 1f).

■ The 3-section cutting blade

is ﬁtted with a plastic cover on delivery.

This must be removed before use and reﬁtted during periods when not

in use.

■ The plastic cover can now be removed.

CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES

■ Fit the cutting ﬁlament protective guard

on the protective guard .

■ The cutting ﬁlament protective guard

must be ﬁtted when working

with the cutting ﬁlament. The cutting ﬁlament protective guard

(pre-ﬁtted on delivery) is ﬁtted as shown in ﬁgure 2a.

■ Ensure that the cutting ﬁlament protective guard

is correctly clicked

into place. There is a blade

on the inside of the cutting ﬁlament pro-

tective guard

. This is covered with a safety cover

(see ﬁg. 2a.).

■ Remove the safety cover

before starting work and replace it after

ﬁnishing work.

CAUTION! SHARP EDGES, WEAR PROTECTIVE GLOVES

■ To remove the cutting ﬁlament protective guard

from the protective

guard

, take a tool, such as a screwdriver, to carefully remove the

three mounting pins.

ATTENTION! RISK OF INJURY!

Hvor kan man købe reservedele? Jeg mangler en fjeder der sidder i huset hvor starts snoren sidder Submitted on 24-3-2021 at 14:32
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBK 4 C2 - IAN 296309 in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FBK 4 C2 - IAN 296309

Florabest FBK 4 C2 - IAN 296309 User Manual - German, Dutch, Danish, French - 78 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Florabest FBK 4 C2 - IAN 296309 Manual

Product: