679143
18
Zoom out
Zoom in
Previous page
1/42
Next page
FBK 4 C2
GB│IE│NI
 13
Turning the engine off
Emergency stop sequence
If the appliance needs to be stopped immediately, turn the On/Off switch
to "0".
Normal sequence
Release the throttle lever
and wait until the engine has slowed down
to its idling speed. Then move the On/Off switch to "0".
CAUTION!
The 3-section cutting blade must be stationary when the engine is
idling. If the 3-section cutting blade is turning, adjust the carburettor!
Working procedures
Before using the appliance, practice all working techniques (see figs. 6a–6c)
with the engine stopped.
Extending the cutting filament
To extend the cutting filament, run the engine at full speed and tap the
strimmer
on the floor. The filament extends automatically. The knife
A
on the cutting filament protective guard
C
cuts the thread to the permissible
length (see fig. 6d).
CAUTION!
Grass/weed residues can get caught under the protective guard
.
Remove the remains using a scraper or similar item when the engine
is switched off.
Various cutting methods
Trimming/mowing (3-section cutting blade or strimmer)
Swing the appliance in a scything motion (see fig. 6a).
Hold the cutting tool parallel to the ground and set the desired cutting
height.
Low trimming (with strimmer)
Hold the appliance with a slight incline to the ground (see fig. 6b).
Always cut away from your body. Never pull the appliance towards
you.
Short mowing (with strimmer)
Short mowing removes all the vegetation right down to the ground.
Angle the strimmer 30° to the right. Set the handle to the desired
position (see fig. 6c).
Cutting against trees/fences/foundations (with strimmer)
NOTE
The filament will wear or fray quickly if it comes into contact with
trees, rocks, walls or foundations. The filament will break off if it
strikes fence mesh.
CAUTION!
Do not use the appliance to remove any objects from footpaths, etc.!
The appliance is powerful and can fling small stones or other objects
15 metres or more and may cause injuries or damage to cars,
houses and windows.
Wear protective goggles!
Seizing
Immediately turn off the engine if the cutting tool becomes blocked.
Remove all grass and scrub from the appliance before restarting the appli-
ance.
Prevent kickback
When working with the 3-section cutting blade there is a risk of kickback if
the blade strikes against solid obstacles (tree trunks, branches, tree stumps,
rocks or similar). This will result in the cutting tool being catapulted back
against the direction of rotation. This can lead to the loss of control of the
appliance. Do not use the cutting blade near fences, metal posts, boundary
stones or foundations. To cut low-density shrubs, position the appliance as
shown in fig. 6e to avoid kickbacks.
Working with the hedge trimmer
Cutting techniques
The double-sided cutter bar allows cutting in both directions or by using
swinging movements from one side to the other.
For a vertical cut, move the hedge trimmer evenly forwards or up and
down in an arc.
For a horizontal cut, move the hedge trimmer in a scything motion
along the edge of the hedge so that cut branches fall to the ground.
See fold-out page (figure A).
NOTE
Remove thicker branches with a branch cutter.
Working with the pole pruner
Sawing techniques
WARNING!
Always pay attention to the falling clippings.
Be aware of the danger of branches swinging back.
NOTE
Place the stop
on the branch. This will help you work more safely
and quietly.
Now you can begin sawing.
Sawing off small branches
Saw small branches (Ø 0–8 cm) from the top down (see figure).
Sawing off larger branches
When sawing larger branches (Ø 8–25 cm), first make a relief cut
A
(see figure). A relief cut also prevents peeling of the bark on the main
trunk.
Saw from the top
B
to the bottom
A
.
2
1
A
B
18


Need help? Post your question in this forum.

Forumrules
1

Forum

florabest-fbk-4-c2---ian-296309

Reset search

  • Hvor kan man købe reservedele? Jeg mangler en fjeder der sidder i huset hvor starts snoren sidder Submitted on 24-3-2021 at 14:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FBK 4 C2 - IAN 296309 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBK 4 C2 - IAN 296309 in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FBK 4 C2 - IAN 296309

Florabest FBK 4 C2 - IAN 296309 User Manual - German, Dutch, Danish, French - 78 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info