456443

Finicompressors Artic 134-EVO luchtdroger Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
40069 Zola Predosa (BO) - ITALY
info@finicompressors.it
- GB -
2.3 INSTALLATION SITE
Particular care is required in selecting the installation site, as an improper location could
jeopardise the proper operation of the dryer. This unit is not suitable to be used in explosive
atmosphere, where risk of fire could exist, or in presence of gaseous or solid polluting material.
Don’t use water to extinguish fire on the dryer on in the surrounding area.
Minimal installation requirements :
•
Select a clean room dry, free from dust, and protected from atmospheric disturbances.
•
The supporting area must be smooth, horizontal and able to hold the weight of the dryer.
•
Minimum ambient temperature of +1 ºC.
•
Maximum ambient temperature of +45 ºC.
•
Allow at list a clearance of 1 m on each side of the dryer for proper ventilation and to facilitate eventual
maintenance operations
.
The dryer doesn't require to be fixed to the supporting surface.
2.4 ASSEMBLING
Operations to be performed by qualified personnel.
Never operate with plants under pressure.
The user is responsible to ensure that the dryer will never be operated with pressure exceeding the
nominal values. Eventual over-pressure could be dangerous both for the operator and the machine.
1
Dryer
2
Cover panel
3
Fixing to compressor
upper screw
4
Compressor
5
Fixing to compressor
lower screw
6
Compression fitting
7
Connection pipe
8
Compression fitting
9
By-pass group
10
Lifting lug
Fig. 1 Fig. 3 Fig. 4
Fig. 2
2
1
6
3
Part. A
5
4
6
7
8
9
3 3
Part. A
10
Assembling sequence :
• Replace the screws No.3 of the compressor, with the (M6x45) fixing screws supplied with the dryer, and
thigh them only partially.
• Tight in the air outlet of compressor the compression fitting No.6, supplied with the assembling kit.
• Remove the cover panel No.2 of the dryer.
• Joint the dryer with the compressor, centring the holes of the dryer frame, with the screws No.3 (Fig. 3).
To lift the dryer from the ground, use the four lifting lug No.10 (M6 with long shank) screwed into the four
holes for cover panel fixing.
• Slide down the dryer, so the screws No.3 occupy the upper part of the holes (Fig. 4).
• Tighten definitively the fixing screws No.3.
• Tight the (M8x25) fixing screws, supplied with the assembling kit, in the position No.5 to fix finally the dryer
to the compressor.
• Put the connection pipe No.7 from the compression fittings No.6 and No.8 and tighten them.
• Connect and properly fasten the condensate drain pipe, in compliance with the instructions given in the
2.7 following chapter.
• Slowly pressurize the plant and check for air leakage.
• Reassemble the cover panel No.2
.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finicompressors Artic 134-EVO luchtdroger at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finicompressors Artic 134-EVO luchtdroger in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info