456445
4
Zoom out
Zoom in
Previous page
1/11
Next page
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 15 of 63
2.2 INSTALLATION SITE
While preparing a proper site for the installation of the dryer, please take into account the following
requirements
The machine must be protected from atmospheric agents and not directly exposed to sun light.
A seating base flat and capable to hold the weight of the machine.
Ambient temperature complying with the nominal data of the dryer.
A clean, dry and properly vented site (we suggest to blow the warm air outside the installation
site).
Make sure to leave sufficient clearance around the dryer in order to allow an adequate cooling of
the machine and for maintenance and/or control operations.
The incoming air must be free from smoke or flammable vapours which could lead to explosion or fire
risks.
2.3 INSTALLATION
Before attempting any installation operation, make sure that
No part of system is under pressure.
No part of the system is electrically powered.
Tubing to be connected to the dryer are impurities free.
After having verified the points listed above, you can proceed to the installation of the machine.
1. Connect the dryer to the compressed air lines indicated in the diagrams below. If not already
existing, we suggest to install a by-pass allowing to insulate the machine from the plant, thus to
facilitate eventual maintenance operations.
2. Check the condensate drainage assembly, and connect the drain flexible hose to the draining line,
keeping in mind that
the condensate separated by the dryer contains oil particles, therefore,
in order to dispose it in compliance with the local rules in force, we suggest a water-oil
separator having adequate capacity.
3. Power the dryer after having checked that the nominal voltage and line frequency are constant
and matching the nominal values of the machine. The user must provide the installation with
an adequate line protection and a ground terminal complying with the electrical rules
locally in force.
1
Air Compressor
2
Aftercooler
3
Condensate Separator
4
Receiver
5
Automatic Drain
6
Particulate Prefilter 5µ (QF)
7 Dryer
8
Solenoid drain valve
9
Desoiling filter 0.10 mg/m3 (PF)
10
Desoiling filter 0.01 mg/m3 (HF)
11
Activated Carbon Filter 0.008 mg/m3 (CF)
12
Water/Oil Separator
In order to optimise the use of the dryer, we suggest to place it in such a way that all the control
instruments of the machine will result easily visible.
Installing a ceramic pre-filter on the air inlet of the dryer, this will be better protected from eventual solid
particles, as it prevents the accumulation of oily materials on the heath exchangers.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finicompressors Artic 134-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finicompressors Artic 134-12 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Finicompressors Artic 134-12

Finicompressors Artic 134-12 User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info