796174
18
Zoom out
Zoom in
Previous page
1/106
Next page
must be switched off and then switched back on
again.
Due to the built-in restart protection, the power
tool cannot be switched on and off via an exter
nal switch module.
Brake
The OF 1010 REBQ has an electronic brake
which brings the spindle with tool to a standstill
within approx. 2 seconds of the tool being
switched off.
7.2 Changing tools
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
To change tools, place the power tool on its
side.
Inserting the tool
Insert the routing tool into the open collet
as far as possible or at least up to the
mark on the router shank.
Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
Tighten the nut [1-5] using an open ended
spanner (WAF 19).
Removing the tool
Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
Undo the nut [1-5] using an open ended
spanner (WAF 19) until you can feel resist
ance. Overcome the resistance by continu
ing to turn the open ended spanner.
Remove the router.
7.3 Changing the collets
Collets are available for the following shaft di
ameters: 6.0 mm; 6.35 mm; 8.0 mm (See
Festool catalogue or online at www.festool.com
for the order numbers)
Completely unscrew the nut [1-5] and re
move it together with the collet.
Only insert a new collet into the spindle if a
nut is fitted and engaged.
Gently screw in the nut. Do not tighten the
nut if no cutter is inserted.
7.4 Setting the routing depth
The routing depth is set in three steps:
1. Set the zero point, see 7.5.
2. Specify the routing depth, see 7.6.
3. Clamp the routing depth, see 7.7.
7.5 Setting the zero point
Release the clamp lever [1-8] so that the
depth stop [1-3] can move freely.
Position the router with the router ta
ble [1-1] on a level surface. Open the rotary
knob [1-7] and push the power tool down
wards until the cutter sits on the surface.
Clamp the power tool in this position by
closing the rotary knob [1-7].
Press the depth stop [1-3] against one of
the three fixed stops of the rotatable step
ped stop [1-2].
A hex key can be used to individually adjust the
height of each fixed stop.
Push the indicator [1-10] downwards so
that it points to 0 mm on the scale.
If the zero position is incorrect, this can be
corrected using the screw on the indica
tor [1-10].
7.6 Specifying the routing depth
The required routing depth can be specified us
ing either quick depth adjustment or fine depth
adjustment.
Quick depth adjustment
Pull the depth stop [1-3] upwards until the
indicator [1-10] points to the required rout
ing depth.
Clamp the depth stop in this position using
the clamp lever [1-8].
Fine depth adjustment
Clamp the depth stop using the clamp lev
er [1-8].
Set the required routing depth by turning
the adjusting wheel [1-9].
Turning the adjusting wheel by a mark
changes the routing depth by 0.1 mm. A
full rotation changes the routing depth by
1 mm. The maximum adjustment range for
the adjusting wheel is 8 mm.
7.7 Clamping the routing depth
Open the rotary knob [1-7] and push the
power tool down until the depth stop touch
es the fixed stop.
Clamp the power tool in this position by
closing the rotary knob [1-7].
English
18
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool OF 1010 REQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool OF 1010 REQ in the language / languages: All languages as an attachment in your email.

The manual is 2.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info