796174

Festool OF 1010 REQ Manual

19
Zoom out
Zoom in
Previous page
1/106
Next page
7.8 Dust extraction
WARNING
Heath hazard posed by dust
► Always work with an extractor.
► Comply with national regulations.
CAUTION! If an anti-static suction hose is not
used, static charge may occur. The user may
receive an electric shock and the electronics of
the power tool may be damaged.
A Festool dust extractor with an extractor hose
diameter of 36 mm or 27 mm (36 mm recom
mended due to the reduced risk of clogging)
can be connected to the extractor connec
tor [1-15].
Chip catcher KSF-OF
KSF-OF chip catcher [3-1] (partly accessory)
consists of a hood and cover and can increase
the efficiency ot the extraction when routing
edges. Installation is similar to that of the copy
ing ring., the cover is attached at the top.
The hood can be cut off along the grooves [3-2]
using a hacksaw and can thus be reduced in
size. The chip catcher can then be used for inte
rior radiuses up to a minimum radius of 40 mm.
8 Working with the electric
power tool
When working on the machine, observe
all of the safety warnings that are listed
at the start as well as the following rules:
– Only guide the power tool towards the
workpiece when it is switched on.
– Always secure the workpiece in such a way
that it cannot move during machining.
– When working, always hold the power tool
with both hands on the handles [1-7] +
[1-13]. This is a prerequisite for precise
work and is essential for plunge-cutting.
Plunge into the workpiece slowly and even
ly.
– When routing, ensure that the power tool's
feed direction is the same as the tool's cut
ting direction, see figure [5].
8.1 Freehand routing
Freehand routing is the method normally used
for lettering or shapes, and for routing edges
using cutters with a guide pin or ring.
8.2 Routing with a parallel side fence
For work running parallel to the workpiece
edge, the supplied parallel side fence [6-4] can
be used.
WARNING
Risk of injury
Upon installation on the wrong side, the
router may touch the parallel side fence.
► Only install the parallel side fence on the
side of the power tool depicted in the im
age [6].
► Clamp the two guide rods [6-7] to the paral
lel side fence using the two rotary
knobs [6-2].
► Insert the guide rods into the grooves of the
router table to the required extent and
clamp them using the rotary knob [6-3].
This distance can be adjusted faster and more
precisely with the fine precision adjust
ment [6-6] available as an accessory:
► Turn the adjusting screw [6-5] in the plastic
part of the guide.
► Clamp the guide rods with the rotating
knobs [6-1] in the precision adjustment.
► Loosen the rotating knobs [6-2] of the par
allel guide.
► Set the desired distance with the adjusting
screw and retighten the rotating knobs.
For better extraxtion, a special suction
hood is available as an accessory for the
side stop.
8.3 Routing with the FS guide system
The guide system (available as an accessory)
makes it easier to route straight grooves.
► Secure the guide rail adapter [7-4] to the
router table using the guide rods [7-3] of
the parallel side fence.
► Secure the guide rail [7-6] to the workpiece
using fastening clamps [7-7].
Ensure that there is a safety distance X of
(see figure [7]) 5 mm between the front
edge of the guide rail and the cutter, or the
groove.
► Place the guide rail adapter on the guide
rail, as shown in figure [7]. To ensure that
the router stop can be guided without play,
use a screwdriver through the top open
ings [7-5] on the side to adjust the two
guidance jaws.
► Tighten the height-adjustable support [7-2]
on the threaded hole of the router table so
English
19
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool OF 1010 REQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool OF 1010 REQ in the language / languages: All languages as an attachment in your email.

The manual is 2.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info