796174
17
Zoom out
Zoom in
Previous page
1/106
Next page
5 Parts of the device
[1-1] Router table
[1-2] Stepped stop
[1-3] Depth stop
[1-4] Locking for trammel unit
[1-5] Nut
[1-6] Spindle stop
[1-7] Handle/Height adjustment
[1-8] Clamp lever
[1-9] Fine adjuster
[1-10] Depth stop indicator
[1-11] Speed adjusting wheel
[1-12] Locking button
[1-13] Handle
[1-14] On/off switch
[1-15] Extractor connector
[1-16] Grooves for guide bars/parallel side
fence
The specified illustrations appear at the begin
ning of the Operating Instructions.
Accessories shown or described are not always
included in the scope of delivery.
6 Commissioning
WARNING
Unauthorised voltage or frequency.
Risk of accidents
The mains voltage and the frequency of the
power source must correspond to the
specifications on the name plate.
In North America, only Festool machines
with the voltage specifications 120 V/60 Hz
may be used.
CAUTION
Heating of the Plug it connection if bayonet
fitting is not completely locked
Risk of burns
Before switching on the power tool, make
sure that the bayonet fitting at the mains
cable is closed fully and locked.
Connect and disconnect the mains power
cable - [2].
6.1 Switching on/off
The switch [1-14] is an on/off switch (press =
ON, release = OFF).
The on/off switch with the locking button [1-12]
can be engaged to operate in continuous mode.
Press the on/off switch again to release the
lock.
7 Settings
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
7.1 Electronics
Speed adjustment
You can continuously adjust the speed within
the speed range using the adjusting
wheel [1-11] (see "Technical data").
This enables you to optimise the cutting speed
to suit each surface.
Material Cutterdiameter [mm] Recom
mended
cutter ma
terial
3 - 14 15 - 25 26 - 35
Rotary controll setting
Hardwood 6 - 4 5 - 3 3 - 1 HW (HSS)
Softwood 6 - 5 6 - 3 4 - 1 HSS (HW)
Laminated
chipboard 6 - 5 6 - 3 4 - 2 HW
Plastic 6 - 4 5 - 3 2 - 1 HW
Alumini
um 3 - 1 2 - 1 1 HSS (HW)
Plaster
board 2 - 1 1 1 HW
Temperature cut-out
Electronic temperature monitoring is integra
ted in order to protect against overheating (mo
tor burnout). The safety electronics system
switches off the motor before a critical motor
temperature is reached. Let the machine cool
down for approximately 3–5 minutes before us
ing it and/or fully loading it again. The cool-
down time is significantly reduced when the
machine is running (no-load).
Restart protection
The built-in restart protection prevents the
power tool from starting up again automatically
if the power is disconnected when the on/off
switch is pressed. In this case, the power tool
English
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool OF 1010 REQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool OF 1010 REQ in the language / languages: All languages as an attachment in your email.

The manual is 2.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info