Manual Ferrex FPCS46 E1 (page 32 of 50) (English)

779780

Zoom out

Zoom in

1/50

Kapitelüberschrift

m NOTICE

If the tree has large prop/buttress roots, these should be removed before the wedge

is cut. If the saw is used for removing the prop/buttress roots, the saw-chain should

not touch the ground so the chain does not become blunt.

Undercut and felling the tree (Fig. 15-16)

• For the undercut, ﬁrst cut the upper part (Pos. 1) of the wedge (Pos. 2). Cut 1/3 of

the way into the tree. Then saw the lower part (Pos. 3) of the wedge (Pos. 2). Now

remove the wedge you have cut out.

• Afterwards, you can carry out the dropping cut on the opposite side of the tree

(Pos. 4). For this, start about 5cm above the middle of the cut. In this way, there is

enough wood between the dropping cut (Pos. 4) and the wedge (Pos. 2) so that it

functions as a hinge. This hinge is designed to guide the tree in the right direc-

tion when falling.

m NOTICE

Before completing the dropping cut, if required, increase the cut using wedges to

control the direction of the fall. Exclusively use wood or plastic wedges. Steel or iron

wedges can cause kickback and damage to the device.

• Be aware of signs that the tree is beginning to fall: Cracking sounds, the drop-

ping cut opening or movement in the upper branches.

• When the tree begins to fall, stop the saw, put it down and leave immediately via

your escape route.

• To prevent injuries, do not cut partly felled trees with your saw. Beware especially

of partly felled trees which are not supported. If a tree does not fall down com-

pletely, remove the saw and help the process along with a cable winch, a pulley

or a towing vehicle.

Sawing a felled tree (log division)

The term “log division“ describes the cutting up of a felled tree into logs of the de-

sired length.

Operating Instructions

How do I download the manual without some scumbag company telling me I have to download their version of PDF????? Submitted on 28-3-2024 at 02:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FPCS46 E1 in the language / languages: English as an attachment in your email.

The manual is 3.57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferrex FPCS46 E1 Manual

Product: