779780

Ferrex FPCS46 E1 Manual

28
Zoom out
Zoom in
Previous page
1/50
Next page
Kapitelüberschrift
32
Starting the engine when cold
Make sure, that the fuel tank is filled with the relevant mixture of petrol and also
top up the chain oil.
1. Activate the chain brake before starting (Fig. 6/pos 3).
2. Switch the stop switch to ‘0’ (OFF) (Fig. 8 / pos 19).
3. Pull the choke (16) fully out until it locks (Fig. 9/arrow direction 1).
4. Push the primer bubble (17) 10 times (Fig. 1).
5. Place the saw on a firm, flat surface. Hold the saw firmly as shown. Pull the
starter handle (6) rapidly 2 times. (Fig. 10) Beware of moving chain!
6. Push in the choke lever as far as it will go (Fig. 9/arrow direction 2).
7. Switch the stop switch to ‘I’ (ON) to start the machine (Fig. 8/ pos. 19).
8. Hold the saw firmly and pull the starter handle (6) rapidly 4 times. Engine
should start (Fig. 10).
m CAUTION
Never allow the starter handle (6) to snap back when it has been pulled out.
This may result in damage.
m CAUTION
Since the choke (Fig. 9/arrow direction 1) is closed, the chain starts to move and ro-
tate AT HIGH SPEED, immediately when the engine is started.
9. Let the engine run for 10 seconds to warm up. Press the safety lock (7) & throttle
lever (18) briefly, the engine will go to ‘idling’ speed (Fig. 11).
m CAUTION
Always pull the starter handle (6) slowly (until you feel the initial resistance) before
pulling it quickly to start the engine.
Do not allow the starter handle (6) to whip back of its own accord.
If the engine does not start up even after several attempts, read the section
‘Troubleshooting’.
Always pull out the starter handle (6) in a straight line. If it is pulled out at an angle,
friction will occur on the eyelet.
As a result of this friction, the starter handle (6) will become frayed and will wear
away faster. Always hold the starter handle (6) when the starter line retracts.
Operation
… 28 …


Need help? Post your question in this forum.

Forumrules
1

Forum

ferrex-fpcs46-e1

Reset search

  • How do I download the manual without some scumbag company telling me I have to download their version of PDF????? Submitted on 28-3-2024 at 02:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FPCS46 E1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FPCS46 E1 in the language / languages: English as an attachment in your email.

The manual is 3.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info