724612
17
Zoom out
Zoom in
Previous page
1/42
Next page
AFTER SALES SUPPORT
(toll free)
e-mail: info.aldi@positecgroup.com1300 889 028
47.1cc Petrol Chainsaw
MODEL: №. 10084 • 08/2019 • FCS4800A
15
The chain tensioning pin (30) must enter the guide bar (19), and the at
faces of both the chainsaw and chain drive side cover (23) must be at
against the bar before the nuts are applied.
10. Fit the chain drive side cover nuts (24) and tighten FINGER TIGHT (Fig M).
Check again the cover is at on the surface of the bar.
11. Rotate the chain (20) a few times to ensure the chain (20) is free to rotate
around the drive sprocket (29) and is correctly engaged on the sprocket.
12. Check the tension of the chain (20). It will need to be tightened. Tighten
the chain tensioning screw (37), in a clockwise direction (previous Fig K)
until the links of the chain just touch the bottom edge of the guide
bar (19).
The chain should be fully seated in the bar channel. DO NOT over tighten.
The chain (20) should be able to be lifted at least 5mm in the centre of the
bar (Fig N).
13. Tighten the chain drive side cover nuts (24) rmly using the supplied
combination tool (bar nut tube spanner) (32) (Fig O).
CAUTION: A new chain (20) will stretch after just a few minutes of use.
Check and, if necessary, re-adjust the chain tensioning screw (37).
A loose chain causes rapid wear to both the chain (20) and the guide bar
(19) and could derail causing a major safety hazard.
NOTE: Do not make ANY adjustments with the chainsaw engine running.
14. To tighten a loose chain (20), loosen the chain drive side cover lock nuts
(24), then using the supplied combination tool (at blade screwdriver)
(32), turn the chain tensioning screw (37) clockwise to tighten the chain
(20) (Fig H). Do not over tighten, the chain (20) should be able to lift 5mm
from the middle of the bar.
15. Retighten the chain drive side cover nuts (24) rmly using the supplied
combination tool (at blade screwdriver) (32) (Fig O). Run the chainsaw
for approximately 30 seconds and then turn the chainsaw o. Retest the
chain.
Assembly
O.M.
TIGHTEN
TIGHTEN
N.
5MM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FCS4800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FCS4800A in the language / languages: English as an attachment in your email.

The manual is 8,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info