Manual Ferrex DX254TS (page 30 of 42) (English)

779800

Zoom out

Zoom in

1/42

Assembly/Setup

Connecting the extraction device (Fig. 13)

A normal household vacuum cleaner is not a suitable extraction device.

1. Connect the suction hose (14) with the suction port (13) and the the saw blade guard (4).

2. Connect the suction hose of a suitable shavings extractor (e.g. a multi-purpose vacuum

cleaner) to the suction port (13) and secure it with a hose clamp.

IX. Setup

Setting the cutting depth (Fig. 1)

Using the crank (12), rotate the saw blade (3) out of the saw table or lower the saw blade into

the table saw. In this way, you can set the desired cutting depth.

-Turn the crank (12) anti-clockwise: increase the cutting depth

-Turn the crank (12) clockwise: reduce the cutting depth

Setting the cutting angle (Fig. 1)

1. Loosen the locking handle (10).

2. Use the crank wheel (11) to set the desired cutting angle on the angle scale.

3. Lock the locking handle (10) to fasten the saw blade (3) at the required angle.

Change the side of the parallel stop (Fig. 12)

1. Unscrew the wing nuts (35) fully.

2. Remove the rail for parallel stop (24) with the big discs (36) and the long carriage bolts

(37) and replace the bolts on the other side of the parallel guide.

3. Slide the rail for parallel stop (24) onto the parallel stop (5), such that the two long car-

riage bolts (37) slides into the guide groove of the rail for parallel stop (24).

4. In order to secure the stop rail on the parallel stop, turn the wing nuts (35) to tighten

them again.

Setting the transverse stop (Fig. 14)

Do not push the stop rail (G) too far towards the saw blade (3). There should be approx. 2 cm of

space between the stop rail and saw blade.

5. Push the transverse stop (2) into one of the two guide slots on the saw table.

6. Loosen the handle (H) and turn the cross guide until you have set it at the required angle.

7. Retighten the handle (H).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex DX254TS in the language / languages: English as an attachment in your email.

The manual is 4.35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferrex DX254TS Manual

Product: