779800

Ferrex DX254TS Manual

28
Zoom out
Zoom in
Previous page
1/42
Next page
26
Assembly
Installing the table extension (Fig. 4)
1. Turn the saw table over and place it on the floor.
2. Plug the connection pieces (23) into the front rail of the table saw.
3. Mount both table extensions (1 / 6) loosely on the saw table with four short hexagon
screws (29), four discs (30) and four nuts M6 (31). To do so, use the corresponding holes
drilled into the saw table.
4. Fix all screws with the spanner (26).
Mounting the frame (Fig. 5 / 6)
Only tighten all screws at this mounting step by hand.
1. Push one rubber foot (22) onto each leg (21).
2. Push the four legs (21) in the slots of the table saw frame.
3. Connect the short table supports (17) and long table supports (18) with the base frame
and left/right table extension (1/6). Use for this four short hexagon screws (29), eight
discs (28), four long hexagon screws (33) and four nuts (31).
4. Secure the four legs (21) with the four oval head screw (32) and four discs (28) at the
front and the back side of the table saw with a screwdriver (not included).
5. Mount the long centre struts (19) and the short centre struts (20) at the legs (21) with 16
carriage bolts (30), 16 discs (28) and 16 nuts (31).
Mounting the tilt protection (Fig. 7)
1. Assemble the tilt protection (16) at the legs (21) at the backside of the table saw by using
four short hexagon screws (29), four discs (28) and four nuts (31).
Inserting the scale (Fig. 8)
1. Turn the saw blade to the maximum position out of the saw table by turning the crank
(12) anti-clockwise until it reaches the stop.
2. Push the scale (38) into the guide groove of the guide rail until it is approximately cen-
tred.
3. Position the parallel stop (5) with open eccentric lever (F) on the guide rail on the sawta-
ble, so that the parallel stop (5) have contact with the saw blade (3).
4. Secure this position by pressing the eccentric lever (F) fully downwards.
5. Align the zero point of the scale (38) with the sight glass of the parallel stop (5) and se-
cure this position with the two screws (39).
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex DX254TS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex DX254TS in the language / languages: English as an attachment in your email.

The manual is 4.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info