762257

Ferm MSM1040 Manual

13
Zoom out
Zoom in
Previous page
1/160
Next page
13
EN
2. Tilt the saw by using the handle (2) until the
indicator (19) reads the desired position on the
scale for bevel angle (20);
3. Tighten the adjusting knob for bevel
adjustment (22).
Switching the machine on/off
Fig. A
• To start the machine, press and hold the lock-
off button (1) and press the on/off switch (3).
• To stop the machine, release the on/off switch
(3).
Making a cross cut
Fig. H, I
Follow these steps to cut perpendicular to the
grain of the wood:
1. Adjust the mitre angle to and the bevel angle to
0°;
2. Move the adjustable fence to the inner
position, towards the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure J.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a mitre cut
Fig. I, J
Follow these steps to make an angled cut to the
face of the wood:
1. Adjust the mitre angle to the desired position
and the bevel angle to 0°;
2. Move the adjustable fence to the inner
position, towards the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure I.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a bevel cut
Fig. K, L
Follow these steps to make an angled cut to the
edge of the wood:
1. Adjust the mitre angle to 0° and the bevel
angle to the desired position ;
2. Move the adjustable fence to the outer
position, away from the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure L.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the
workpiece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a compound cut
Fig. L, M
Follow these steps to make a combination of
mitre and bevel cut:
1. Adjust the mitre angle and the bevel angle to
the desired position ;
2. Move the adjustable fence to the outer
position, away from the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure L.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the
workpiece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1040 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 17,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info