762257

Ferm MSM1040 Manual

11
Zoom out
Zoom in
Previous page
1/160
Next page
11
EN
Do not under any circumstances use
grinding discs as the cutting tool.
Before replacing the saw blade, it is strongly
advised to set the mitre angle and bevel angle to
0°. Otherwise, access could be limited.
• Disconnect the machine from the power supply.
• Remove the screw (33) that holds the retraction
arm to the blade cover.
• Remove the screw (40) in order to remove
the bolt-cover by lifting the blade cover (5)
upwards.
• Both saw blade bolt (42) and Flange (41) should
be visible now like shown in fig. E.
• Press the saw blade lock button (43) Rotate
the saw blade carefully by hand until the blade
locks.
• Use hex key to remove the saw blade bolt (42)
by loosening in a clockwise direction.
• Remove the Flange (41) and the saw blade
• Replace the saw blade making sure that the
arrow marked on the saw blade must point in
the same direction as the arrow shown marked
on the machine. The saw blade teeth must
point downwards.
• Fix the saw blade bolt (42) use the saw blade
lock button (43) in order to secure tightly
• Lower the blade cover (5) in order for the bolt
cover to fall back into place and tighten the
screw (40)
• Attach the retraction arm back onto the blade
cover (5) by tightening the screw (33)
• Rotate the saw blade and check if the guard
operates freely
Dust extraction
Fig. A, B, T
Provide good ventilation at the
workplace.
Wear dust protection.
The dust from materials such as lead paint and
some types of wood can be harmful to your
health. Breathing in this dust can cause allergic
reactions and/or cause respiratory illnesses for
the user or people in the near vicinity. Certain
dusts, such as oak or beech dust, are classified
as carcinogenic, especially in conjunction with
wood treatment additives (chromate, wood
preservative). We strongly advise to use a dust
extraction system that is suitable for the material
wherever possible.
Avoid dust accumulation at the
workplace. Dust can easily ignite.
The dust extraction system can be blocked by
dust, chips or fragments of the workpiece. Thus, it
must be cleaned regularly. To do so:
1. Disconnect the mains plug from the power
supply.
2. Wait until the saw blade has come to a
complete stop.
3. Remove any blockage if necessary
Mounting the dust bag
Fig. A, B
Press in the clamp of the dust bag (26) and
slide it onto the dust outlet (28) on the back of
the machine. The dust bag stays in place when
releasing the clamp.
Connecting a vacuum cleaner
Fig. A, B, T
The dust extractor must be suitable for
the material being worked.
When vacuuming dry dust that is
especially detrimental to health or
carcinogenic, use a special dust extractor.
A vacuum cleaner hose can be connected to the
dust outlet (28). To do so, simply connect the
vacuum hose to the dust extraction spout.
4. OPERATION
Before you turn on the machine, always
check that the saw blade is fitted
correctly. The blade must turn smoothly.
Always check the protective guards
before use.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1040 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 17,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info