762257

Ferm MSM1040 Manual

10
Zoom out
Zoom in
Previous page
1/160
Next page
10
EN
and tighten the locking bolt for slide rails (29);
3. Press the handle (2) fully downwards;
4. Lock the position lock knob (38) by first pulling
and then turning it;
5. Wind up the mains cable and tie it together
with the supplied cable strap.
After locking the transport position, use the
carrying handle (27) to safely carry and transport
the machine.
Only use the carrying handle to transport
the machine and never the protective
guards.
Install of a stationary machine
Fig. A, B, C
To ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use. You can install the machine in
three ways:
1. On a workbench
In this case the machine must be secured to the
workbench using suitable screw fasteners. Use
the four holes (12) to do this. As shown on fig. C.
2. On a subframe
Read all the warnings and instructions
included with the saw stand. Failure to
observe the warnings and follow
instructions may result in electric shock,
fire and/or serious injury.
Assemble the saw stand properly before
mounting the power tool. Correct
assembly is important to prevent the risk
of collapsing.
In this case the machine must be secured to the
sub frame with bolts. Use the four holes (12) to
do this. The sub frame must be anchored with 4
bolts to the floor plate with dimensions of at least
1 square meter. Mount the power tool on the saw
stand in the transport position.
3. Flexible installation
This type of installation is not
recommended by the manufacturer.
If, in exceptional circumstances, it is not possible
to mount the power tool on a flat and stable work
surface, you can improvise by setting it up with
the tilt protectors.
Without the tilt protector, the power tool
will not be stable and can tip over
especially when sawing maximum mitre
and/or bevel angles.
• Rotate the front tilt protector (37) inwards or
outwards until the power tool is positioned
level on the work surface.
Checking the protective guard
Fig. A
The Retracting protective guard (5) protects
against accidental contact with the saw blade and
from saw chips flying around. Before use, it must
be checked if the saw blade guard is functioning
correctly. To do so, pull the handle (2) downwards
and check the following:
• The Retracting protective guard (5) must
provide access to the saw blade (6) without
getting in contact with other parts.
• When folding the saw upwards into the
starting position, the Retracting protective
guard (5) must cover the entire saw blade (6)
automatically.
Replacing the saw blade
Fig. D, E, F
Before carrying out any work on the
machine, disconnect the mains plug
from the power supply.
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond
with the characteristic data given in the
operating instructions. Use only saw
blades that are marked with a speed
equal or higher than the speed marked
on the machine.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1040 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 17,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info