Manual Ferm MSM1040 (page 14 of 160) (English, German, Dutch, French, Italian, Turkish, Spanish)

762257

Zoom out

Zoom in

1/160

Using the slide function

Fig. A

For extra wide workpieces, the machine is

equipped with a sliding function. When using the

slide function, make sure to loosen the locking

bolt for slide rails (29). Pull the handle (2) away

from the fence (9) until the saw blade is in front

of the workpiece. Slowly guide the tool arm

downwards using the handle and afterwards

push the handle (2) towards the fence (9) and saw

through the workpiece with uniform feed.

For small workpieces, it is possible to fix the

sliding function in the rear position of the saw with

the locking bolt for slide rails (29). If more cutting

width is desired, then it is necessary to loosen the

locking bolt for slide rails (29).

Adjusting the depth stop

Fig. N

The depth stop can be adjusted, to limit the

cutting depth. This can be used to easily saw a

groove. To do so:

1. Move the plate for depth adjustment (45) to the

left.

2. Adjust the knob for depth adjustment (24) to

the desired depth;

Switching the laser on/off

Fig. G, O

Press the laser switch (46) to switch the laser on

or off.

Fine-tuning

Prior to any adjustment work disconnect

the mains power plug.

To ensure precise cuts, the basic settings of the

saw must be checked and adjusted before first

use, as well as necessary after intensive use.

Suitable special tools are required for this. Ferm

after-sales will help handling this work quickly and

reliably.

Fine-tuning the laser

Fig. O

If the laser (18) ceases to indicate the correct

cutting line, you can readjust the laser. To do so:

• Loosen the laser adjustment screws (48) and

set the laser by moving it until the laser beam

strikes the teeth of the saw blade (6).

Fine-tuning the 0° bevel angle

Fig. P, Q

1. Adjust the mitre and bevel angle to 0°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking

bolt for slide rails (29);

4. Set an angle gauge to 90° and place it on the

table (11), as shown on figure Q. The leg of the

angle gauge must be flush with the saw blade

(6) along its entire length;

5. Loosen the lock nut for 0° bevel angle (50);

6. Adjust the stop bolt for 0° bevel angle (32) until

the leg of the angle gauge is flush with the saw

blade along its entire length;

7. Re-tighten the lock nut for 0° bevel angle (50).

Subsequently check the position of the angle

indicator (19). If necessary loosen the pointer

using a Philips screwdriver, set to position 0° on

the scale for bevel angle (20) and re-tighten the

retaining screw.

Fine-tuning the 45° bevel angle (Fig. P, R)

1. Adjust the mitre and bevel angle to 45°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking

bolt for slide rails (29);

4. Set an angle gauge to 45° and place it on the

table (11), as shown on figure R. The leg of the

angle gauge must be flush with the saw blade

(6) along its entire length;

5. Adjust the stop bolt for 45° bevel angle (31)

until the leg of the angle gauge is flush with the

saw blade along its entire length;

Subsequently check the position of the angle

indicator (19). If necessary loosen the pointer

using a Philips screwdriver, set to position 45° on

the scale for bevel angle (20) and re-tighten the

retaining screw.

Fine-tuning the 0° mitre angle

Fig. B, G, S

1. Set an angle gauge to 0° on the table (11) and

position it between the fence (9) and the saw

blade (6);

2. The leg of the angle gauge must be flush with

the saw blade (6) along its entire length;

3. Loosen all four fence bolts (51) and adjust the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1040 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 17,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1040 Manual

Product: