634078

Ferm MSM1030 - FKZ-210 Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
GB
8
Ferm
Motor
Connect the machine to a 220/230 V socket.•
If the motor does not start, immediately •
release the switch. Take the plug out of the
socket. Check that the saw blade can turn
freely. If so, try starting the machine again.
To prevent damaging the motor must be
regularly freed of chips and dust to
ensure correct cooling.
If the motor suddenly stops while sawing, let •
go of the switch immediately. Loosen the saw
blade from the piece of work, after which
sawing can continue.
Using long cables of too small a diameter can •
result in loss of voltage, which can lead to
problems with the motor.
For a length up to 15 metres a cable must •
be used with a diameter of 1.5 mm
2
.
For a length of between 15 and 40 metres •
a cable must be used with a diameter of
2.5 mm
2
.
3. ASSEMBLY AND
ACCESSORIES
Installation of the machine on a workbench or
on the subframe.
This machine is a stationary machine and for
safety reasons must always be firmly installed
and not used for mobile applications.
You can install the machine in two ways:
a. As a stationary machine on a workbench. In
this case the machine must be secured to the
workbench with 4 bolts.
b. As a stationary machine on the subframe.
In this case the machine must be secured to
the subframe with 4 bolts and the subframe
anchored to the floor or to a floor plate with
dimensions of at least 1 square metre.
Mounting and removing the saw blade
Fig. A+B
Do not use the machine without the
guard.
Mounting
Pull out the locking knob (3) and raise the saw •
head (12).
Loosen the bracket (29) by removing the •
screw (30).
Raise the guard (6).•
Keep the spindle lock button (7) pressed and •
loosen the bolt (19) using the spanner (20).
Remove the flanges (21 & 22).•
If necessary, clean the flanges (21 & 22).•
Mount the flange (22).•
Mount the saw blade (5). Make sure that the •
arrow on the saw blade points in the same
direction as the arrow on the saw head.
Mount the flange (21).•
Keep the spindle lock button (7) pressed and •
tighten the bolt (19) using the spanner (20).
Lower the guard (6).•
Mount the bracket (29) by tightening the •
screw (30).
Removing
Pull out the locking knob (3) and raise the saw •
head (12).
Loosen the bracket (29) by removing the •
screw (30).
Raise the guard (6).•
Keep the spindle lock button (7) pressed and •
loosen the bolt (19) using the spanner (20).
Remove the flange (21).•
Remove the saw blade (5).•
Mount the flange (21).•
Keep the spindle lock button (7) pressed and •
tighten the bolt (19) using the spanner (20).
Lower the guard (6).•
Mount the bracket (29) by tightening the •
screw (30).
Setting the mitre angle
Fig. C
The mitre angle is left/right variable between •
0° and 45°. The mitre angle can be read from
the scale (9).
Do not set the mitre angle during use.
Slacken the locking knob (8).•
Turn the saw table (13) to the required •
position.
Tighten the locking knob (8).•
Setting up the double sawing angle / mitring
Fig. D
Adjust the first angle as described for •
adjusting the saw angle (above).
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1030 - FKZ-210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1030 - FKZ-210 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info