Manual Ferm MSM1030 - FKZ-210 (page 9 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

634078

Zoom out

Zoom in

1/72

Ferm

Turn the knob (10) anticlockwise and then set •

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(10) again by turning it clockwise.

Changing the carbon brushes

Fig. A

Make sure that the plug is not in the socket!•

Unscrew the covers (16) with a flat bladed •

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(16) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. F

Press in the clamp of the dust bag (27) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. OPERATION

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

Set the desired sawing angle of the machine.•

Put the plug into the socket.•

Fix the piece of work in place using the •

clamps (24): make sure that the material is

well clamped in place!

Hold the material tightly on the left side while •

making sure that you keep a safe distance

from the blade of the saw.

Turn on the machine using the switch (1).•

Make sure that the saw blade has reached full •

speed before allowing it to touch the piece of

work to be sawn.

Use knob (2) to raise the protective cover •

lock.

Now bring the saw slowly downwards so that •

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

Bring the machine gently up again and switch •

it off by letting go of the switch (1).

5. SERVICE & MAINTENANCE

Always make sure that the machine is

not connected to the mains electricity

when you carry out any maintenance of

the mechanism.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Problem solving

1. The motor does not start

The plug is not in the socket•

The power cord is broken•

The switch is defective. Take the machine to •

your Ferm dealer for repair.

2. The saw cut is not even (jagged)

The saw blade must be sharpened•

The saw blade is mounted back to front•

The saw blade is clogged with resin or sawdust•

The saw blade is not suitable for the piece of •

work being used

3. The height and/or mitre lever is obstructed

Chips and/or dust must be removed•

4. The motor has difficulty in reaching full

speed

The extension cord is too thin and/or too long•

The mains voltage is less than 230 V•

5. The machine vibrates excessively

The saw blade is damaged•

6. The machine becomes excessively hot

The ventilation slots are blocked. Clean them •

out with a dry cloth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1030 - FKZ-210 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1030 - FKZ-210 Manual

Product: