110130
12
Zoom out
Zoom in
Previous page
1/62
Next page
Ferm 113
Stop aldrig savklingen ved at udøve tryk på den fra siden.
Forvis dig om, at den bevægelige beskyttelseskap kan bevæges frit. Forvis dig også
om, at den mekanisme, hvormed beskyttelseskappen skubbes tilbage i lukket stilling,
virker upåklageligt.
Blokér ikke den bevægelige beskyttelseskappe i åben stilling.
Vær ved savning af træ opmærksom på knaster, søm, revner og/eller aflejring af
smuds. Savning af dette træ kan føre til den farlige situation, at rundsaven løber fast.
Efterlad aldrig rundsaven uden tilsyn.
Brug maskinen udelukkende til savning af træ.
Sikkerheds tips ved anvendelse af laser lyset
Se aldrig direkte ind i lysstrålen på laseren.
Sigt aldrig på mennesker og dyr med laser lysstrålen.
Sigt ikke lysstrålen mod meget reflekterende materiale. Skade kan forekomme fra det
reflekterende lys.
Få kun reparationer af laseren foretaget af kyndigt personale / professional
reparationsspecialister.
Isæt ingen hårde objekter i laserens øje.
Rengør laser øjet med en blød tør børste.
Når rundsaven er i brug
Arbejdsemnet skal klemmes godt fast.
Trærester eller lignende, der er i umiddelbar nærhed af saven, må ikke fjernes med
hånden. Når trærester har sat sig fast mellem faste og/eller bevægelige dele, skal
maskinen stoppes og netstikket trækkes ud af stikkontakten, før træresterne fjernes.
Sørg for, at rundsaven tilkobles ubelastet. (Undlad at rundsaven kommer i kontakt
med arbejdsemnet, når den kobles til). Rundsaven skal først have nået det maksima-
le omdrejningstal.
Sav ikke arbejdsemner, der er tykkere end savens dybde.
Forvis dig om, at der ikke er elektriske kabler, vandrør eller gasledninger, når du
saver i vægge eller gulve.
Sluk først for rundsaven og vent til savklingen er kommet helt til stilstand, før du fjer-
ner rundsaven fra arbejdsemnet og lægger maskinen til side.
Maskinen skal slukkes øjeblikkeligt, når:
Stikket eller netledningen er defekt, eller hvis ledningen er beskadiget.
Afbryderen er defekt.
Rundsaven er overophedet.
Der er røg eller det lugter af svedet isolationsmateriale.
Elektrisk sikkerhed
Ved anvendelse af elektriske mas kiner skal man altid følge de lokalt gældende sikker-
hedsforskrifter i forbindelse med brandfare, fare for elektrisk stød og legemensbeskadigel
-
se. Læs udover de nedenstående instruktioner også sikkerhedsforskrifterne i den separat
vedlagte sikkerhedsfolder. Bevar instruktionerne godt!
UK
D
NL
F
E
P
I
S
SF
N
DK
12
Ferm
When inserting the batteries, ensure that the +/- terminals are correctly placed, as shown
inside the battery compartment.
Check that the laser beamer is properly closed by carefully opening the lid straight
upwards. If the lid opens up, repeat the closing procedure, until the lid stays properly
closed.
Adjusting the laser beam
Transport handling and heavy use can affect the precision of the laser beam.
The laser beam itself can be easily adjusted.
Hold the blade of the circular saw against a straightedge or perfectly straight plank.
Switch the laser on.
Check whether the laser beam runs parallel along the edge of the straightedge or plank.
If the laser beam is out of alignment, proceed as follows:
Loosen the screw on the front side of the laser a few turns.
Hold the blade of the circular saw against a straightedge or perfectly straight plank.
Correct the laser such that it runs dead straight along the edge.
Again tighten the screw.
5. MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on
the motor.
The machines have been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper machine care
and regular cleaning.
Troubleshooting
Below we have listed a few probable causes and solutions to which you can refer if your
circular saw does not function properly.
The temperature of the
electric motor exceeds
70°C.
The tool does not work
when switched on.
The motor has been
overloaded by working
it too hard.
The motor is defective.
Damaged cord and/or
plug.
Defective switch.
Cut more slowly and
allow the motor to cool
down.
Please contact the
service address on the
warranty card.
Check cord and/or
plug.
Please contact the
service address on the
warranty card.
GB
D
NL
F
E
P
I
S
SF
N
DK
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FKS 185 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info