Manual Ferm FKS 185 L (page 13 of 62) (English, German, Dutch, Danish, French, Italian, Norwegian)

110130

Zoom out

Zoom in

1/62

Ferm 13

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine.

Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Replacing hte carbon brushes

Fig. E

• Remove the screws (1).

• Withdraw the carbon brushes (2) from the circular handsaw and inspect them for

wear.

• Place the carbon brushes back in the brush holders provided.

• Check that the copper contact on the carbon brushes makes good contact with the

copper part in the brush holder.

• Replace the screws (1) and tighten them firmly.

Frequent use will cause the carbon brushes to wear down. Regular inspection,

after every 30 hours of use, is essential. If the brushes have worn down to less

than 4 mm, replace.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the

warranty card. In the back of this manual you find an exploded view showing the parts

that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore please make use of options for recycling

the packaging.

• When cutting it is very

difficult to move the

work forward in a

straight line and the cut

is not clean.

• The circular saw

makes a lot of noise

and/or does not run

smoothly.

• The blade is bent or

blunt.

• The carbon brushes

are worn.

Replace the blade.

• Please contact the

service address on the

warranty card.

112

Ferm

c) Når en sav genstartes i arbejdsemnet, skal savklingen centreres i savsnittet, og det

skal kontrolleres, at tænderne ikke sidder fast i materialet. Hvis en savklinge binder,

kan den bevæge sig op eller forårsage tilbageslag fra arbejdsemnet, når saven star-

tes igen.

d) Understøt store arbejdsemner for at minimere risikoen for klemning af klingen med til-

bageslag til følge. Store arbejdsemner kan bøje under deres egen vægt. Der skal

anbringes støtter under emnet i begge sider, tæt ved skærelinjen og tæt ved emnets

kant.

e) Benyt aldrig sløve eller beskadigede savklinger. Uskærpede eller ukorrekt lagte sav-

klinger danner smalle savsnit, som forårsager for høj gnidningsmodstand, klemning af

savklingen og tilbageslag.

f) Savklingens dybde og låsearme til skråsnit skal være sikkert tilspændt, før der saves.

Hvis savklingens justering ændrer sig under savning, kan det forårsage binding af

savklingen og tilbageslag.

g) Vær særligt forsigtig ved "styrtsavning" ind i vægge og andre afdækkede områder.

Savklingen kan komme til at stikke ud og skære i genstande, som kan forårsage tilba-

geslag.

Sikkerhedsinstruktioner for underskærmen

a) Kontroller før hver anvendelse, at underskærmen lukker korrekt. Brug ikke saven,

hvis underskærmen ikke bevæger sig frit og lukker øjeblikkeligt. Klem eller bind aldrig

underskærmen fast i åben position. Hvis saven tabes, kan underskærmen blive bøjet.

Løft underskærmen med trækarmen og kontroller, at den bevæger sig frit og ikke har

kontakt med savklingen eller nogen anden del - i alle skærevinkler og -dybder.

b) Kontroller funktionen af underskærmens fjeder. Hvis skærmen og fjederen ikke funge-

rer korrekt, skal de repareres før brug. Underskærmen kan arbejde trægt på grund af

beskadigede dele, klistrede aflejringer eller ophobning af restmateriale.

c) Underskærmen bør kun trækkes tilbage manuelt ved specialsavning som f.eks. "styrt-

savning" eller "kombineret savning". Løft underskærmen med trækhåndtaget. Så

snart savklingen går ind i materialet, skal underskærmen frigives. Til alle andre former

for savning, skal underskærmen fungere automatisk.

d) Kontroller altid, at underskærmen dækker savklingen, før saven anbringes på bænk

eller gulv. En ubeskyttet fritløbende klinge vil få saven til at bevæge sig bagud og

save i alt, den møder på sin vej. Vær opmærksom på den tid, det tager for savklingen

at standse, efter at kontakten slippes.

Inden rundsaven tages i brug

• Kontrollér følgende:

• Kontrollér, at motorens tilslutningsspænding svarer til netspændingen.

• Kontrollér, at netkablet og stikket er i god stand.

• Kontrollér, at savklingen ikke mangler tænder og at den er fri for revner og eller

spalter. Hvis dette er tilfældet, skal savklingen udskiftes med det samme.

• Kontrollér, at savklingen er monteret korrekt.

• Brug ikke savklinger, der er deformeret eller beskadiget.

• Brug ikke HSS-klinger.

• Brug kun savklinger, der er i overensstemmelse med de angivne mål og beskrivelsen.

Brug ikke savklinger, hvis krop er bredere eller hvis fortanding er smallere end spal-

tekniven.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 5,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FKS 185 L Manual

Product: