110130
11
Zoom out
Zoom in
Previous page
1/62
Next page
Ferm 11
And that the toothed wheel does not protrude more than 5 mm beyond the lower
edge of the splitting wedge.
The splitting wedge must always be used except when cutting into the middle of the
workpiece.
Allow the safety guard to return over the saw blade by releasing the knob (1).
Press the shaft locking knob (2) back in, refit the retaining ring (5) and tighten the
hexagon screw firmly once more.
4. OPERATION
Use of hearing protection is recommended while operating the circular saw.
Switching On/Off
Fig. E
Press knob (B) with your right-hand thumb and keep it depressed.
Press knob (A) to start the saw.
Release knob (A) to stop the saw.
Operation
Hold the work using clamps or a vice to have both hands free to operate the saw.
Switch on the saw and place the bottom plate on the work.
Slowly move the saw towards the previously drawn cutting line and slowly press the
tool forward.
Firmly press the bottom plate on the work, otherwise the circular saw may start to
vibrate, causing the blade to break more easily.
Let the saw do the job. Do not put undue pressure on the circular saw.
Laser beamer
Laser beamer in use
The leading beam of the laser beamer makes sawing in straight lines much easier:
a) Along a drawn line, or
b) Byaligning it to a fixed point marked on the workpiece.
The range of the laser beam, depending on the environmental light, is about 65 cm.
Replacing batteries
Fig.C
Lock the machine in its highest position
Unscrew the screw and remove the cover.
Replace the batteries with new ones. You will need 2 x 1.5 V “Micro/AAA” batteries.
Never dispose of old/empty batteries with the household refuse, but deposit them instead
at special collection point for batteries or chemical refuse.
GB
D
NL
F
E
P
I
S
SF
N
DK
114
Ferm
Kontroller altid om netspændingen svarer til værdien på typeskiltet.
Maskinen er dobbeltisoleret; det er derfor ikke nødvendigt med en jordledning.
Udskiftning af ledninger eller stik
Hvis netledningen er blevet beskadiget, skal den udskiftes med en speciel netledning, som kan
fås via fabrikanten eller fabrikantens kundeservice. Gamle ledninger og stik skal kasseres, når
de er blevet udskiftet med nye. Det er farligt at sætte stikket på en løs ledning i en stikkontakt.
Ved brug af forlængerledninger
Brug udelukkende godkendte forlæn gerledninger, der er beregnede til maskinens effekt.
Lederne skal have et gennemsnit på mindst 1.5 mm
2
. Hvis forlængerledningen sidder på
en tromle, rulles ledningen helt af.
3. MONTAGE OG INDSTILLINGS FORSKRIFTER
Inden indstillingen af rundsaven påbegyndes, skal du forvisse dig om, at stik-
ket er trukket ud af stikkontakten.
Indstilling af savevinkel (skråvinkel)
Fig. B
Løsn begge knapper (1).
Drej bundpladen i den korrekte position (0° - 45°) og stram knapperne igen.
Savevinklen (skråvinkel) kan aflæses på vinkelmåleren (2).
Montering af kløveanlægsfladen
Fig. B
Løsn knappen (3).
Sæt kløveanlægsfladen i de forhåndenværende spalter (4).
Indstil den korrekte skærebredde og stram knappen igen (3).
Indstilling af skæredybde
Fig. A
Løsn knappen (4).
Før bundpladen (17) nedad.
Savklingens skæredybde kan aflæses på siden af sikkerhedsskærmen.
Stram spændeknappen (4) igen, når den korrekte dybde er indstillet.
Udskiftning eller rengøring af savklingen
Fig. D
Brug aksellåseknappen (2) for at forhindre akslen i at dreje.
Løsn derefter sekskantskruen (3) midt i savklingen, med den medfølgende sekskantnøgle.
Drej sikkerhedsskærmen tilbage, og hold den der ved hjælp af knappen (1).
UK
D
NL
F
E
P
I
S
SF
N
DK
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FKS 185 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info