110130
10
Zoom out
Zoom in
Previous page
1/62
Next page
Ferm 115
Træk stopringen og savklingen ud og gør savklingen ren eller udskift den med en ny.
Sæt igen savklingen tilbage på akslen. Sørg for at savklingens tænder peger i samme
retning som spaltekniven (4).
Sørg for, at delekniven indstilles således, at
Afstanden mellem den og tænderne på savklingen ikke er over end 5 mm.
Tænderne på savklingen ikke stikker mere end 5 mm frem foran underkanten af
delekniven.
Delekniven skal altid bruges, undtagen når der saves ind i midten af arbejdsemnet.
Lad sikkerhedsskærmen vende tilbage over savklingen ved at løsne knappen (1).
Tryk aksellåseknappen (2) i igen, monter stopringen (5) igen og stram sekskantskruen
godt igen.
4. BETJENING
Det anbefales at bruge høreværn, når der arbejdes med rundsaven.
Tilkobling/Frakobling
Fig. E
Tryk på knappen (B) med højre hånds tommelfinger og hold knappen trykt ned.
Tryk derefter på knappen (A). Rundsaven starter nu.
Rundsaven stopper, når du slipper knappen (A).
Ibrugtagning
Klem arbejdsemnet fast, således at begge hænderne er fri til at fastholde og betjene
rundsaven.
Tilkobl rundsaven og placér savebunden på arbejdsemnet.
Tryk forsigtigt på rundsaven og bevæg den langsomt frem langs den på forhånd teg-
nede skærelinie.
Tryk savebunden fast mod arbejdsemnet.
Lad rundsaven gøre arbejdet! Undlad derfor at udøve for meget tryk på rund-
saven.
Laser Lys
Laser lyset i brug
Det ledende laser lys gør det meget lettere at save i lige linjer:
a) Langs en optegnet linje, eller
b) Ved at stille det på linje med at fast punkt markeret på objektet.
Laser lysets rækkevidde, afhængig af det omkringværende lys, er omkring 65 cm.
Placering af batterier
Fig.C
Lås maskinen i dens højeste position.
UK
D
NL
F
E
P
I
S
SF
N
DK
10
Ferm
Replacing cables or plugs
If the mains cable becomes damaged, it must be replaced with a special mains cable
available from the manufacturer or the manufacturer’s customer service. Dispose of old
cables or plugs immediately after replacing them with new ones. It is dangerous to con-
nect the plug of a loose cable to a socket.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The mini-
mum conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel completely.
3. ASSEMBLY AND ADJUSTING INSTRUCTIONS
Before adjusting the saw, make sure the plug is removed from the socket.
Setting the sawing angle (bevel)
Fig. B
Loosen both knobs (1).
Rotate the soleplate to the correct position (0° - 45°), and tighten the knobs. The
sawing angle (bevel) can be read on the protractor (2).
Fitting the ripfence
Fig. B
Loosen knob (3).
Insert the rip fence into the slots provided (4).
Set the correct cut width and tighten the knob (3).
Setting the cutting depth
Fig. A
Loosen knob (4).
Move the soleplate (17) downwards.
The cut depth of the saw blade can be read off on the side of the safety guard.
Tighten the clamping knob (4) once the correct depth is set.
Exchanging or cleaning the saw blade
Fig. D
Use the shaft locking knob (2) to prevent the shaft from rotating.
Next loosen the hexagon screw (3) in the centre of the saw blade, using the Allen key
provided.
Turn the safety guard to the rear, and hold it there with the aid of the knob (1).
Withdraw the retaining ring and the saw blade, and clean the saw blade, or replace it
with a new one.
Again place the saw blade back on the shaft. Ensure that the teeth of the saw blade
are pointing in the same direction as the riving knife (4).
Ensure that the splitting wedge is set in such a way that
The gap between it and the toothed wheel rim of the saw blade does not exceed 5 mm
GB
D
NL
F
E
P
I
S
SF
N
DK
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FKS 185 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FKS 185 L in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm FKS 185 L

Ferm FKS 185 L User Manual - English, German, Dutch, Danish, French, Italian, Norwegian - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info