Manual Ferm fks 165 (page 7 of 50) (English, German, Dutch, French, Italian, Norwegian)

383705

Zoom out

Zoom in

1/50

Ferm 07

• Switch off the tool and wait until the blade has stopped completely before moving the

saw away from the work or putting it down. Hearing protection should be worn when

using circular saw.

Switch off the machine immediately when you discover:

• A defective mains plug or mains lead;

• A defective switch.

• Overheating of the circular saw.

• Smoke or odeur caused by scorched insulation.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country

to reduce the risk of fire, electric shock and personal injury. Read the following safety

instructions and also the enclosed safety instructions.

Keep these instructions in a safe place!

Always check that the power supply corresponds to the voltage on the rating plate.

Class II machine – Double insulation – You don’t need any earthed plug.

Replacing cables or plugs

If the mains cable becomes damaged, it must be replaced with a special mains cable

available from the manufacturer or the manufacturer’s customer service. Dispose of old

cables or plugs immediately after replacing them with new ones. It is dangerous to

connect the plug of a loose cable to a socket.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine. The

minimum conductor size is 1.5 mm

. When using a cable reel always unwind the reel

completely.

3. ASSEMBLY AND ADJUSTING INSTRUCTIONS

Before adjusting the saw, make sure the plug is removed from the socket.

Setting the sawing angle (bevel)

Fig. B.

• Loosen both knobs (1).

• Rotate the soleplate to the correct position (0° - 45°), and tighten the knobs. The sawing

angle (bevel) can be read on the protractor (2).

Fitting the rip fence

Fig. B.

• Loosen knob (3).

• Insert the rip fence into the slots provided (4).

• Set the correct cut width and tighten the knob (3).

94 Ferm

Montering af kløveanlægsfladen

Fig. B.

• Løsn knappen (3).

• Sæt kløveanlægsfladen i de forhåndenværende spalter (4).

• Indstil den korrekte skærebredde og stram knappen igen (3).

Indstilling af skæredybde

Fig. C.

• Løsn knappen (1).

• Før bundpladen (2) nedad.

• Savklingens skæredybde kan aflæses på siden af sikkerhedsskærmen.

• Stram spændeknappen (1) igen, når den korrekte dybde er indstillet.

Udskiftning eller rengøring af savklingen

Fig. D.

• Brug aksellåseknappen (2) for at forhindre akslen i at dreje.

• Løsn derefter sekskantskruen (3) midt i savklingen, med den medfølgende

sekskantnøgle.

• Drej sikkerhedsskærmen tilbage, og hold den der ved hjælp af knappen (1).

• Træk stopringen og savklingen ud og gør savklingen ren eller udskift den med en ny.

• Sæt igen savklingen tilbage på akslen. Sørg for at savklingens tænder peger i samme

retning som spaltekniven (4).

• Sørg for, at delekniven indstilles således, at

• afstanden mellem den og tænderne på savklingen ikke er over end 5 mm.

• tænderne på savklingen ikke stikker mere end 5 mm frem foran underkanten af

delekniven.

• Delekniven skal altid bruges, undtagen når der saves ind i midten af arbejdsemnet.

• Lad sikkerhedsskærmen vende tilbage over savklingen ved at løsne knappen (1).

• Tryk aksellåseknappen (2) i igen, monter stopringen (5) igen og stram sekskantskruen

godt igen.

Udskiftning af kulbørster

Fig. E.

• Fjern skruerne (1).

• Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.

• Sæt kulbørsterne tilbage i de forhåndenværende holdere.

• Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i

børsteholderen.

• Sæt skruerne (1) i igen og stram dem godt.

Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne

kontrolleres regelmæssigt efter hver 30 driftstimer. Hvis kulbørsterne er kortere

end 4 mm, skal de udskiftes med nye.

4. BETJENING

Det anbefales at bruge høreværn, når der arbejdes med rundsaven.

mi servono i ricambi per una sega circolare FKS-165 1200 wat,n.17 e n.25 e n.16
Submitted on 22-2-2021 at 19:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 165 in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 5,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fks 165 Manual

Product: