Manual Ferm fks 165 (page 8 of 50) (English, German, Dutch, French, Italian, Norwegian)

383705

Zoom out

Zoom in

1/50

Ferm 93

• Sørg for, at rundsaven tilkobles ubelastet. (Undlad at rundsaven kommer i kontakt med

arbejdsemnet, når den kobles til). Rundsaven skal først have nået det maksimale

omdrejningstal.

• Sav ikke arbejdsemner, der er tykkere end savens dybde.

• Forvis dig om, at der ikke er elektriske kabler, vandrør eller gasledninger, når du saver i

vægge eller gulve.

• Sluk først for rundsaven og vent til savklingen er kommet helt til stilstand, før du fjerner

rundsaven fra arbejdsemnet og lægger maskinen til side.

Maskinen skal slukkes øjeblikkeligt, når

• Stikket eller netledningen er defekt, eller hvis ledningen er beskadiget.

• Afbryderen er defekt.

• Rundsaven er overophedet.

• Der er røg eller det lugter af svedet isolationsmateriale.

Elektrisk sikkerhed

Ved anvendelse af elektriske mas kiner skal man altid følge de lokalt gældende

sikkerhedsforskrifter i forbindelse med brandfare, fare for elektrisk stød og

legemensbeskadigelse. Læs udover de nedenstående instruktioner også sikkerheds-

forskrifterne i den separat vedlagte sikkerhedsfolder.

Bevar instruktionerne godt!

Kontroller altid om netspændingen svarer til værdien på typeskiltet.

Klasse II maskine – Dobbelt isolering – Du behøver ingen jordforbindelsestik.

Udskiftning af ledninger eller stik

Hvis netledningen er blevet beskadiget, skal den udskiftes med en speciel netledning, som kan

fås via fabrikanten eller fabrikantens kundeservice. Gamle ledninger og stik skal kasseres, når

de er blevet udskiftet med nye. Det er farligt at sætte stikket på en løs ledning i en stikkontakt.

Ved brug af forlængerledninger

Brug udelukkende godkendte forlæn gerledninger, der er beregnede til maskinens effekt.

Lederne skal have et gennemsnit på mindst 1.5 mm

. Hvis forlængerledningen sidder på en

tromle, rulles ledningen helt af.

3. MONTAGE OG INDSTILLINGS FORSKRIFTER

Inden indstillingen af rundsaven påbegyndes, skal du forvisse dig om, at stikket er

trukket ud af stikkontakten.

Indstilling af savevinkel (skråvinkel)

Fig. B.

• Løsn begge knapper (1).

• Drej bundpladen i den korrekte position (0° - 45°) og stram knapperne igen. Savevinklen

(skråvinkel) kan aflæses på vinkelmåleren (2).

08 Ferm

Setting the cut depth

Fig. C.

• Loosen knob (1).

• Move the soleplate (2) downwards.

• The cut depth of the saw blade can be read off on the side of the safety guard.

• Tighten the clamping knob (1) once the correct depth is set.

Exchanging or cleaning the saw blade

Fig. D.

• Use the shaft locking knob (2) to prevent the shaft from rotating.

• Next loosen the hexagon screw (3) in the centre of the saw blade, using the Allen key

provided.

• Turn the safety guard to the rear, and hold it there with the aid of the knob (1).

• Withdraw the retaining ring and the saw blade, and clean the saw blade, or replace it with a

new one.

• Again place the saw blade back on the shaft. Ensure that the teeth of the saw blade are

pointing in the same direction as the riving knife (4).

• Ensure that the riving knife is set in such a way that

• the gap between it and the toothed wheel rim of the saw blade does not exceed 5 mm

• and that the toothed wheel does not protrude more than 5 mm beyond the lower edge

of the splitting wedge.

• The riving knife must always be used except when cutting into the middle of the workpiece.

• Allow the safety guard to return over the saw blade by releasing the knob (1).

• Press the shaft locking knob (2) back in, refit the retaining ring (5) and tighten the hexagon

screw firmly once more.

Replacing the carbon brushes

Fig. E.

• Remove the screws (1).

• Withdraw the carbon brushes (2) from the circular handsaw and inspect them for wear.

• Place the carbon brushes back in the brush holders provided.

• Check that the copper contact on the carbon brushes makes good contact with the copper

part in the brush holder.

• Replace the screws (1) and tighten them firmly.

Frequent use will cause the carbon brushes to wear down. Regular inspection,

after every 30 hours of use, is essential. If the brushes have worn down to less than

4 mm, replace.

4. OPERATION

Use of hearing protection is recommended while operating the circular saw.

Switching on/off

Fig. E.

• Depress knob (B) with your right-hand thumb and keep it depressed.

• Depress knob (A) to start the saw.

• Release knob (A) to stop the saw.

mi servono i ricambi per una sega circolare FKS-165 1200 wat,n.17 e n.25 e n.16
Submitted on 22-2-2021 at 19:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 165 in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 5,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fks 165 Manual

Product: