Manual Ferm fks 165 (page 9 of 50) (English, German, Dutch, French, Italian, Norwegian)

383705

Zoom out

Zoom in

1/50

Ferm 09

Operation

• Hold the work using clamps or a vice to have both hands free to operate the saw.

• Switch on the saw and place the bottom plate on the work.

• Slowly move the saw towards the previously drawn cutting line and slowly press the tool

forward.

• Firmly press the bottom plate on the work, otherwise the circular saw may start to vibrate,

causing the blade to break more easily.

Let the saw do the job. Do not put undue pressure on the circular saw.

5. MAINTENANCE

Make sure that the machine is not live when carrying out maintenance work on the

motor.

The machines have been designed to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon proper machine care and

regular cleaning.

Troubleshooting

Below we have listed a few probable causes and solutions to which you can refer if your circular

saw does not function properly.

1. The temperature of the electric motor exceeds 70°C.

• The motor has been overloaded by working it too hard.

Cut more slowly and allow the motor to cool down.

• The motor is defective.

Contact your local dealer to have the tool inspected and/or repaired.

2. The tool does not work when switched on.

• Damaged cord and/or plug.

Check cord and/or plug.

• Defective switch.

Contact your local dealer to have the switch inspected and/or repaired.

3. When cutting it is very difficult to move the work forward in a straight line and the cut

is not clean.

• The blade is bent or blunt.

Replace the blade.

4. The circular saw makes a lot of noise and/or does not run smoothly.

• The carbon brushes are worn.

Contact your local dealer to have your tool inspected and/or repaired.

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the

engine.Regularly clean the machine housing with a soft cloth, preferably after each use.

Keep the ventilation slots free from dust and dirt. If the dirt does not come off use a soft

cloth moistened with soapy water.

92 Ferm

f) Savklingens dybde og låsearme til skråsnit skal være sikkert tilspændt, før der saves.

Hvis savklingens justering ændrer sig under savning, kan det forårsage binding af

savklingen og tilbageslag.

g) Vær særligt forsigtig ved "styrtsavning" ind i vægge og andre afdækkede områder.

Savklingen kan komme til at stikke ud og skære i genstande, som kan forårsage

tilbageslag.

Sikkerhedsinstruktioner for underskærmen

a) Kontroller før hver anvendelse, at underskærmen lukker korrekt. Brug ikke saven,

hvis underskærmen ikke bevæger sig frit og lukker øjeblikkeligt. Klem eller bind aldrig

underskærmen fast i åben position. Hvis saven tabes, kan underskærmen blive bøjet.

Løft underskærmen med trækarmen og kontroller, at den bevæger sig frit og ikke har

kontakt med savklingen eller nogen anden del - i alle skærevinkler og -dybder.

b) Kontroller funktionen af underskærmens fjeder. Hvis skærmen og fjederen ikke

fungerer korrekt, skal de repareres før brug. Underskærmen kan arbejde trægt på

grund af beskadigede dele, klistrede aflejringer eller ophobning af restmateriale.

c) Underskærmen bør kun trækkes tilbage manuelt ved specialsavning som f.eks.

"styrtsavning" eller "kombineret savning". Løft underskærmen med trækhåndtaget. Så

snart savklingen går ind i materialet, skal underskærmen frigives. Til alle andre former

for savning, skal underskærmen fungere automatisk.

d) Kontroller altid, at underskærmen dækker savklingen, før saven anbringes på bænk

eller gulv. En ubeskyttet fritløbende klinge vil få saven til at bevæge sig bagud og

save i alt, den møder på sin vej. Vær opmærksom på den tid, det tager for savklingen

at standse, efter at kontakten slippes.

Inden rundsaven tages i brug

• Kontrollér følgende:

• Kontrollér, at motorens tilslutningsspænding svarer til netspændingen.

• Kontrollér, at netkablet og stikket er i god stand.

• Kontrollér, at savklingen ikke mangler tænder og at den er fri for revner og eller spalter.

Hvis dette er tilfældet, skal savklingen udskiftes med det samme.

• Kontrollér, at savklingen er monteret korrekt.

• Brug ikke savklinger, der er deformeret eller beskadiget.

• Brug ikke HSS-klinger.

• Brug kun savklinger, der er i overensstemmelse med de angivne mål og beskrivelsen.

Brug ikke savklinger, hvis krop er bredere eller hvis fortanding er smallere end

spaltekniven.

• Stop aldrig savklingen ved at udøve tryk på den fra siden.

• Forvis dig om, at den bevægelige beskyttelseskap kan bevæges frit. Forvis dig også om, at

den mekanisme, hvormed beskyttelseskappen skubbes tilbage i lukket stilling, virker

upåklageligt.

• Blokér ikke den bevægelige beskyttelseskappe i åben stilling.

• Vær ved savning af træ opmærksom på knaster, søm, revner og/eller aflejring af smuds.

Savning af dette træ kan føre til den farlige situation, at rundsaven løber fast.

• Efterlad aldrig rundsaven uden tilsyn.

• Brug maskinen udelukkende til savning af træ.

Når rundsaven er i brug

• Arbejdsemnet skal klemmes godt fast.

• Trærester eller lignende, der er i umiddelbar nærhed af saven, må ikke fjernes med

hånden. Når trærester har sat sig fast mellem faste og/eller bevægelige dele, skal

maskinen stoppes og netstikket trækkes ud af stikkontakten, før træresterne fjernes.

mi servono i ricambi per una sega circolare FKS-165 1200 wat,n.17 e n.25 e n.16
Submitted on 22-2-2021 at 19:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 165 in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 5,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fks 165 Manual

Product: