Manual Ferm fks 165 (page 5 of 50) (English, German, Dutch, French, Italian, Norwegian)

383705

Zoom out

Zoom in

1/50

Ferm 05

Secure the workpiece to a stable platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss of control.

e) Hold power tool by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire

will also make exposed metal parts of the power tool "live" and shock the operator.

f) When ripping always use a rip fence or straight edge guide. This improves the

accuracy of cut and reduces the chance of blade binding.

g) Always use blades with correct size and shape (diamond versus round) of arbour

holes. Blades that do not match the mounting hardware of the saw will run

eccentrically, causing loss of control.

h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt

were specially designed for your saw, for optimum performance and safety of operation.

Causes and operator prevention of kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing

an uncontrolled saw to lift up and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls

and the motor reaction drives the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of

the blade can dig into the top surface of the wood causing the blade to climb out of

the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and position your arms to resist

kickback forces. Position your body to either side of the blade, but not in line with the

blade. Kickback could cause the saw to jump backwards, but kickback forces can be

controlled by the operator, if proper precautions are taken.

b) When blade is binding, or when interrupting a cut for any reason, release the trigger

and hold the saw motionless in the material until the blade comes to a complete stop.

Never attempt to remove the saw from the work or pull the saw backward while the

blade is in motion or kickback may occur. Investigate and take corrective actions to

eliminate the cause of blade binding.

c) When restarting a saw in the workpiece, centre the saw blade in the kerf and check

that saw teeth are not engaged into the material. If saw blade is binding, it may walk

up or kickback from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of blade pinching and kickback. Large

panels tend to sag under their own weight. Supports must be placed under the panel

on both sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before making

cut. If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a "plunge cut" into existing walls or other blind areas.

The protruding blade may cut objects that can cause kickback.

Safety instructions lower guard

a) Check lower guard for proper closing before each use. Do not operate the saw if

lower guard does not move freely and close instantly. Never clamp or tie the lower

guard into the open position. If saw is accidentally dropped, lower guard may be bent.

96 Ferm

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at

fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak,

osv. Den slags stoffer beskadiger kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan

bestilles.

Miljø

For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så

vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.

Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres

på en genbrugsplads.

Garanti

Læs det separat vedlagte garantikort for garantibetingelserne.

CE KONFORMITETSERKLÆRING (DK)

Vi erklærer herved, udelukkende på eget ansvar, at dette

FKS-165

opfylder følgende standarder eller standardiserede dokumenter:

EN60745-1, EN60745-2-5, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

i henhold til bestemmelserne i direktiverne:

98/37/EC, 73/23/EEC, 89/336/EEC, 2002/95/EC, 2002/96/EC

01-09-2006

ZWOLLE NL

J.A. Bakker - van Ingen J. Lodewijk

CEO Ferm BV Quality Manager Ferm Global

Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor

til enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.

Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • Holland

mi servono i ricambi per una sega circolare FKS-165 1200 wat,n.17 e n.25 e n.16
Submitted on 22-2-2021 at 19:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 165 in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 5,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fks 165 Manual

Product: