763247

Ferm AGM1048 - FAG-115-500 Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
EN
7
Ferm
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is
damaged and needs replacing, it is important that
it is correctly destroyed and replaced by an
approved BS 1363/5A fused plug and that the
following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
blue neutral
brown live
As the colours of the wires in the mains cable of
the unit may not correspond to the coloured
markings identifying the terminals in the plug,
proceed as follows:
- The wire which is coloured blue must be
connected to the terminal which is marked
with the letter N or coloured black.
- The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
Technical data
Mains voltage 230-240 V~
Mains frequency 50 Hz
Power input 500 W
No-load speed 11,000 /min
Grinding disc Ø 115 mm
Bore Ø 22 mm
Spindle thread M14
Weight 1.5 kg
Sound pressure (Lpa) 86 dB(A)
Acoustic power (Lwa) 97 dB(A)
Uncertainty (K) 3 dB(A)
Vibration 3.13 m/s2
Uncertainty (K) 1.5 m/s2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in EN
60745; it may be used to compare one tool with
another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signifi cantly reduce the exposure level
Protect yourself against the effects of
vibration by maintaining the tool and its
accessories, keeping your hands warm, and
organizing your work patterns
Wear ear and eye protection
Description
Fig. A
Your angle grinder has been designed for grinding
and cutting masonry and steel.
This machine, in combination with the
included grinding guard, is only suitable
for grinding operations. Cutting
operations with bonded abrasive cut-off
wheels are only allowed when a cut-off
guard (Fig D, available as optional
accessory 300802) is used.
1. On/off switch
2. Spindle lock button
3. Carbon brush cap
4. Guard
5. Main grip
6. Auxiliary grip
Assembly
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the guard
Fig. B
Do not use the machine without the
guard.
Mounting
Place the machine on a table with the spindle •
(3) facing upwards.
Keep the spindle lock button (2) pressed and •
remove the flange (7) using the flange key (8).
If necessary, remove the grinding disc (9).•
Remove the flange (10).•
Mount the guard (4). Secure the guard (4) by •
tightening the screw (11) and the nut (12).
Mount the flange (10).•
If necessary, mount the grinding disc (9).•
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm AGM1048 - FAG-115-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1048 - FAG-115-500 in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info