763247

Ferm AGM1048 - FAG-115-500 Manual

8
Zoom out
Zoom in
Previous page
1/16
Next page
EN
8Ferm
Keep the spindle lock button (2) pressed and •
mount the flange (7) using the flange key (8).
Removing
Place the machine on a table with the spindle •
(3) facing upwards.
Keep the spindle lock button (2) pressed and •
remove the flange (7) using the flange key (8).
If necessary, remove the grinding disc (9).•
Remove the flange (10).•
Remove the guard (4) by loosening the screw •
(11) and the nut (12).
Mount the flange (10).•
If necessary, mount the grinding disc (9).•
Keep the spindle lock button (2) pressed and •
mount the flange (7) using the flange key (8).
Mounting and removing the grinding disc
Fig. B
Do not use the machine without the
guard.
Mounting
Place the machine on a table with the guard •
(4) facing upwards.
Keep the spindle lock button (2) pressed and •
remove the flange (7) using the flange key (8).
Mount the grinding disc (9).•
Keep the spindle lock button (2) pressed and •
mount the flange (7) using the flange key (8).
Removing
Place the machine on a table with the guard •
(4) facing upwards.
Keep the spindle lock button (2) pressed and •
remove the flange (7) using the flange key (8).
Remove the grinding disc (9).•
Keep the spindle lock button (2) pressed and •
mount the flange (7) using the flange key (8).
Mounting and removing the auxiliary grip
Fig. C
Mounting
Tighten the auxiliary grip (6) into one of the •
mounting holes (13).
Removing
Loosen the auxiliary grip (6) from the mounting •
hole (13).
Use
Switching on and off
Fig. A
To switch on the machine in continuous mode, •
slide the on/off switch (1) in the direction of the
grinding disc.
To switch off the machine, press the lower part •
of the on/off switch (1).
Hints for optimum use
Clamp the workpiece. Use a clamping device •
for small workpieces.
Draw a line to define the direction in which to •
guide the grinding disc.
Hold the machine with both hands.•
Switch on the machine.•
Wait until the machine has reached full speed.•
Place the grinding disc on the workpiece.•
Slowly move the machine along the pre-drawn •
line, firmly pressing the grinding disc against
the workpiece.
Do not apply too much pressure on the •
machine. Let the machine do the work.
Switch off the machine and wait for the •
machine to come to a complete standstill
before putting the machine down.
Cleaning and maintenance
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Regularly clean the housing with a soft cloth.•
Keep the ventilation slots free from dust and •
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
Replacing the grinding disc
Fig. B
Worn or damaged grinding discs must be replaced
immediately.
Only use sharp and undamaged grinding
discs.
To remove the old grinding disc (9), proceed •
as described in the section
”Mounting and removing the grinding disc”.
To mount the new grinding disc (9), proceed •
as described in the section
”Mounting and removing the grinding disc”.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm AGM1048 - FAG-115-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1048 - FAG-115-500 in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info