Manual Faber GV36TT (page 23 of 36) (English, German, Dutch, French)

461221

Zoom out

Zoom in

1/36

23 < < < <

3.5 Remote control general

The remote control is solely meant for adjusting the flame height. It is not possible to

ignite the pilot flame with the remote control. For igniting the pilot flame please refer to

chapter 3.4

The remote control has a built-in thermostat that allows adjustment of the ambient

temperature within certain limits, and it is also fitted with a timer.

The receiver (fig. 1.2) as well as the gas control unit (fig. 1.3/1.4) can be found behind

the:

control cover, a drawer at the bottom or behind a frame.

 The remote control has 4 buttons. (fig.1.1)

 The LED-light on the receiver will light up when there is a good reception, and it

will blink when button B has reached one of its limits.

 Place the remote control in the wall bracket when you use the Thermostat/Timer

function

 Mount the included wall bracket within 4 metres of the hearth (fig. 2.1/2.2/2.3).

3.5.1 Placing the batteries in the remote control unit

 Remove the lid at the back of the remote control unit. (fig. 2.1)

 Place a 9

Volt MN1604/6LR61 Alkaline long life battery.

 Close the lid.

3.5.2 Placing the batteries in the receiver

 Take the

receiver (fig. 1.2) out of the gas block support.

 Remove the lid of the receiver.

 Place 4 AA/LR6 Alkaline long life batteries (fig. 2.2).

 Close the lid and replace the receiver set in the gas block support.

3.5.3 Replacing empty batteries

 Han

dset: If the indication BATT appears in the top right hand corner of the display,

the batteries of the remote control need replacing.

 Receiver: When the LED-light on the receiver weakens, the batteries of the

receiver need replacing.

After replacement of the batteries in the handset the values of the thermostat and timer

have been reset back to factory settings.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Faber GV36TT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Faber GV36TT Manual

Product: