473611
6
Zoom out
Zoom in
Previous page
1/13
Next page
Le cappe Faber ti aiutano nell’installazione
perché hanno:
Collaudo
1 - Mettere in funzione il motore
2 - Accendere le luci
Se la cappa è aspirante verificare che sia ben colle-
gata alla tubazione d’uscita.
Se la cappa è filtrante verificare che ci siano i filtri
carbone.
Prima pulizia
• Staccare le pellicole protettive
• Eliminare le impurità con una spugna umida e
poco sapone neutro
• Risciacquare con un panno umido
• Asciugare con un panno morbido, se la cappa è
inox seguire la satinatura dell’acciaio
• Si può dare alla cappa inox un trattamento protet-
tivo con la salvietta Faber Clin&Clin
Kit Aspirazione Remota - Consente di spostare il motore
della cappa in un punto remoto all’interno dell’abitazione.
Il Remote Blower può essere collocato in tre diffe-
renti posizioni.
ATTENZIONE: È necessario cambiare la posizio-
ne della flangia del foro d’entrata a seconda della
collocazione scelta. Il Remote Blower deve essere
connesso alla cappa ed al condotto di uscita con un
tubo del diametro di Ø 150 mm.
Consultare il manuale d’installazione
allegato nell’imballo.
Distanza di installazione
La cappa va installata ad una misura minima di 65 cm dal piano cottura.
ATTENZIONE: la garanzia non è valida se tale distanza di sicurezza non è rispettata.
La cappa non garantisce le prestazioni dichiarate se la distanza dal piano cottura supera i 75 cm.
Alcuni modelli ad installazione verticale (es. Mirror, Matrix) si installano più in basso. Confrontare il ma-
nuale tecnico del prodotto.
Installation distance
The hood is to be installed at a minimum distance of 65 cm from the cooking top.
ATTENTION: the product guarantee will not be considered valid if this distance is not respected.
The hood may not reach declared performance levels if the distance from the cooking top exceeds 75 cm.
Some vertical-installation models (ex. Mirror, Matrix) are to be installed lower. Check the product’s
technical manual.
Faber hoods are easy to install because they have:
Inspection
1 - Turn on the motor
2 - Switch on the lights
If the hood is an extraction hood, verify that it is
properly connected to the exit tubing.
If the hood is a filtering hood, verify that the charcoal
filters have been inserted.
First cleaning
• Remove the protective films
• Remove impurities with a damp sponge and a
small amount of neutral soap
• Rinse with a damp cloth
• Dry with a soft cloth. If the hood is in stainless
steel, continue with a steel glaze
• You can give stainless steel hoods a protective
treatment with the Faber Clin&Clin tissue
Remote Blower Kit - If this kit is used, the cooker hood
motor may be moved to a remote location within the
home, signifi cantly reducing the noise level.
The blower can be positioned in three different ways.
ATTENTION: Basing on the chosen direction it is
necessary to change position of the air inlet flange
with the cover. The blower has to be connected to
the hood and to the external air outlet with ø 150
mm tubes.
Please check the instructions manual
contained in the hood packaging.
Appendere la cappa
Hang the hood
Mettere a squadro
Align
Collegare la tubazione
Connect tubing
Inserire il camino
Insert the chimney
8
ACCADEMIA | ACADEMY
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Algemeen at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Algemeen in the language / languages: English, Italian as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Faber Algemeen

Faber Algemeen Quick start guide - All languages - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info