Manual FAAC 455 (page 15 of 28) (English)

119529

Zoom out

Zoom in

1/28

Page 15

January, 2004

412 Operator And

455 D Control Panel Installation Manual

THE 455 D CONTROL PANEL INSTALLATION INSTRUCTIONS

RADIO

1-455D115 = 115V

1-455D = 230V

+OP -CL

+24 VFS W

NC -B -

STOP

A + TX

FS W

W. L.

LOCK

9 10 11 12 13 14 15 16 17 18 19

22 23 24 25

LA MPCOMOP CL

MOTOR 1

MOTOR 2

CLCOMOP

1 2 3 4 5 6 7 8

20 21

FC A 1

FC A 2

FC C 2

FC C 1

V1- 4

61C455D

F-+

N L

MA IN

CONNECT THE OPERATOR(S) TO THE

ONTROL PANEL

WARNING!

Turn the main power off before

you make any electrical connections or before

programming.

CAUTION: The operators are grounded only by

the grounded circuit the installer provides.

USING A JUNCTION BOX

If an operator is more than 2 ft away from the control

panel, you must use a junction box for connection.

Use a U. L. Listed cord grip where the operator cord

enters the junction box.

Note: If you have a one-leaf gate design, the

operator must be connected to Motor 1

(terminals 1,2, & 3)

To wire up motor 1, connect the white wire to

terminal 1(on the J4 terminal strip), the black wire to

2, and the red wire to 3. Wire each leg of the capacitor

(supplied) to terminals 2 & 3.

Note: If you want to delay the closing of one

gate leaf in a two-leaf gate design, be sure to

connect its operator to Motor 1.

In order to wire motor 2 in a bi-parting system,

connect the white wire to terminal 4 (on the J4

terminal strip), the black wire to 5, the red wire to 6.

Wire each leg of the capacitor (supplied) to terminals

5 & 6.

CHECK THE MOTOR’S DIRECTION OF

OTATION

After you have connected the main power supply, and

the operator(s) to the control panel, you need to

check the direction of rotation for each operator

motor in your gate design.

Note: To check a motor’s direction of rotation,

you must have three closed circuits on terminal

block J1. Install one circuit between terminals 11

and 16, another circuit between terminals 12

and 19, and another circuit between terminals

13 and 19.

Figure 13. The 455 D Control Panel

J3 terminal block for

main power supply

J4 terminal block for

connecting the operator

(s)

J1 terminal block for low-

voltage accessories

J2 quick connector port

F Function Push Button

— Programming Push

Button

+ Programming Push

Button

FUSES

220

VAC

115

VAC

Main Power

5 A 10 A

Accessories

800

Looking for set up program for 455A control board to FAAC 760 dual gate
Submitted on 9-7-2023 at 01:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of FAAC 455 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of FAAC 455

FAAC 455 User Manual - Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

FAAC 455 Manual

Product: