Allows all chrono-thermostat functions to be enabled or disabled.
Sub-menu M2 – 2 PROGRAM DAY
The daily programmable chrono-thermostat functions can be enabled, disabled and set.
Two on/off times can be set defined by the times set according to the table below, where the OFF setting tells the clock to ignore the command:
Sub-menu M2 – 3 PROGRAM WEEK
The weekly programmable chrono-thermostat functions can be enabled, disabled and set.
The weekly programmer has 4 independent programs whose final effect involves the combination of the 4 individual programs. The programmer can be
enabled or disabled. Moreover, if the time is set to OFF, the time clock ignores the corresponding control.
In each program you will find: Switch-on time, Switch-off time, Set stove heat output, Room temperature, Days of the week for which the programme is
to be active. Monday is 1 and Sunday is 7.
Caution: set carefully to prevent overlapping of different activation times of different programmes on the same day.
Sub-menu M2 – 4 PROGRAM WEEK-END
The programmable chrono-thermostat functions can be enabled, disabled and set for the week-end (days 5 and 6, or Saturday and Sunday).
SUGGESTION: if you still do not know exactly the result you want to obtain, enable only one programme at a time to avoid confusion and unwanted
stove switching on and off.
Disable the daily programme if you want to use the weekly programme. If you use the weekly programme for 1, 2, 3 and 4 programmes, never enable
the week-end programme.
Always disable the weekly programme before enabling the week-end programme.
Menu 03 – SELECT LANGUAGE
Use this command to select one of the languages available.
Menu 04 – MODE STAND-BY
Activates the "STAND-BY" mode that switches the appliance off after the room temperature has been higher than SET after the time defined by a pre-set parameter,
or when the external thermostat is satisfied.
After switching off after this condition, restarting will only be possible when the following condition is verified: the actual room temperature is lower than the set one,
after which the appliance will switch on automatically once the pre-set time has elapsed.
Menu 05 – MODE BUZZER
Set it to “OFF” to disable the buzzer.
Menu 06 – LOAD INITIAL
This function is important if the product is new, or if it is switched off due to insufficient pellets in the hopper.
INITIAL IGNITION MUST BE PERFORMED BY AUTHORISED PERSONNEL ONLY, NOT BY THE PURCHASER.
CONTACT THE SUPPORT CENTRE TO SEND A SPECIALIST TECHNICIAN.
It allows a pellet preload to be carried out for a predefined time when the product is switched off and cold. Start with button P1 and stop with button P4. The initial
load is only enabled if the appliance is in the Off state.
Menu 07 – STATE STOVE
It displays the instant status of the appliance reporting the status of the various devices connected to it. A few examples are included in the following pages. The
following will be displayed: status times (including on, off, working, etc.), pellet load and heat output, fume temperature and fume motor speed.
Menu 08 – SETTINGS TECHNIC
Menu only for technicians and installers.
11. USER FUNCTIONS
Standard operation of a control board properly installed in a stove is described below with reference to the functions available to users. The indications listed below
refer to a control board fitted with programmable chrono-thermostat.
Stove ignition
Ensure that there are pellets in the hopper, that the burn pot is correctly positioned and free from any combustion residues and then close the door. To turn the unit
on, press button P4 for a few seconds. The display shows that the stove is on.
Start-up phase
The appliance performs the start-up phases in sequence according to the methods defined by the parameters that manage levels and times. The display will show
the wording START, as there is no pellet loading but the exhaust blower is in operation. LOAD PELLET state will occur where the pellets are being loaded into the
burn pot. Once the pellets have started to burn and the fume temperature increases, the display will show the wording FLAME LIGHT, a transition phase between
ignition and operating heat output.
Ignition fault
If the fume temperature has not reached the minimum permitted value after a predefined time, at a rate of 2°C/min, the appliance goes into alarm status.
If there are unburnt pellets inside the burn pot, it is necessary to empty the burn pot before switching the stove on again. Pellet waste and potential bursting inside
the combustion chamber will thus be avoided.
If the pellets have begun to burn but the alarm state persists, wait until all the pellets are burning and then switch on again.
Check that there are pellets inside the hopper.
Stove operational
At the end of the start-up phase, if no problems occurred, the stove enters its normal working mode.
When the fume temperature is the same as that set by the parameters, the fan is switched on.
Once the set temperature has been reached, the appliance will go into MODUL- and automatically work at minimum power.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eva Calor ARIA 50 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eva Calor ARIA 50 in the language / languages: English as an attachment in your email.
The manual is 7.33 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
